Weider 831.159831 Press a 2 Square Inner Cap 67 into the Press Top Frame, On bottom, Into

Page 9

10.Press a 2” Square Inner Cap (67) into the Press Top Frame (9).

Attach the Press Top Frame (9) to the indicated bracket at the top of the Press Upright (5) with

two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86).

Do not tighten the Nylon Locknuts yet.

11.Identify the Left Weight Guides (27), which have welded rings near the bottom. Slide two Weight

Bumpers (46) onto the Left Weight Guides.

Note:

The wide end of the Weight Bumpers must be

on bottom.

Insert the Left Weight Guides

into the

indicated holes in the Center Base (2).

Set the other two Weight Bumpers (46) over the

indicated holes in the Center Base (2). Note: The wide end of the Weight Bumpers must be on

bottom. Insert the Right Weight Guides (26) through the Weight Bumpers and into the holes in the Center Base.

12. Attach the indicated Weight Guides (26, 27) to

the Center Base (2) with two 3/8” x 2 3/4” Bolts (82), four 3/8” Washers (97), and two 3/8” Nylon Locknuts (90).

9

10

 

89

 

 

 

 

 

 

 

67

 

 

109

 

 

 

9

 

 

 

5

 

 

 

 

86

11

 

 

 

 

26

27

 

 

 

 

 

 

 

Welded

 

 

 

Rings

 

 

46

 

 

 

2

 

12

 

26

 

 

 

 

 

 

27

 

 

 

90

90

 

 

 

 

 

 

97

 

82

97

 

 

 

 

 

 

 

2

 

 

82

 

Image 9
Contents Serial Number Decal Model No Serial NoSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Cable Assembly AssemblyArm Assembly To open the parts bag for that stageFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the bottom On the Short Weight TubeLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as shown in stepNylon Locknuts yet Nylon JamnutsAssembly Pulley BAG 2. Remove one V-Pulley Pages 30 Identify the Butterfly CableBag for identification of the Pro Pulleys Bracket onBracket On the back of the Butterfly Upright Labeled Pulley BAGEd as shown Identify the Rear CablePulley and the pin on the Upright Identify the Ab Cable 74. It is approximately103 Large tabsRemove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Be removed in step Direction shownPulley Is attached as shownIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley With the 3/8 Nylon Jamnut Cable Trap 38 to the 3/8 x 4 3/4 BoltIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down High Press LEG Weight Resistance ChartLEG LOW Pulley ARM Press Lbs Left TopTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No