Weider 831.159831 user manual Locate and open the parts bag labeled, Frame Assembly

Page 6

Frame Assembly

1.Before beginning, be sure that you have read and understood the information on page 5.

Locate and open the parts bag labeled

“FRAME ASSEMBLY.”

Press a 2” Square Inner Cap (67) into each end of the Butterfly Base (1).

Insert four 5/16” x 2 1/2” Carriage Bolts (75) and a a 3/8” x 3 1/2” Carriage Bolt (95) up through the indicated holes in the Butterfly Base (1). Place the

Butterfly Base flat on the floor. Note: If the Bolts fall out, secure them by putting a small piece of

tape over the head of each Bolt.

2. Press three 2” Square Inner Caps (67) into the

Center Base (2). Insert a 3/8” x 3 1/2” Carriage Bolt (95) up through the indicated hole in the

Center Base.

Attach the Center Base (2) to the Butterfly Base (1) with two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86)Do. not tighten the Nylon Locknuts yet.

Note: There are three kinds of Support Plates. The main difference between them is the dis- tance between the holes. When you need a Support Plate, find the kind with holes that will fit over the bolts you are using.

3.Press a 2” Square Inner Cap (67) into the end of the Press Base (3).

Insert four 5/16” x 2 1/2” Carriage Bolts (75) up through the indicated holes in the Press Base (3).

Insert a 3/8” x 2 1/2” Carriage Bolt (76) and a 3/8” x 4” Carriage Bolt (112) up through the indicated

holes at the end of the Press Base.

Attach the Press Base (3) to the Center Base (2) with two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86)Do. not tighten the Nylon Locknuts yet.

6

1
					67
	1				95
					95
			75
	75
67
2
89	109
		86			67
					67
1	86	2
			95
3
				86	67
	2				67
	2
		86			109
	3
					89
			75	76	112
			75

	75

Image 6

Contents SEARS, Roebuck and CO Hoffman ESTATES, IL Model No Serial NoSerial Number Decal Patent PendingTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Arm Assembly AssemblyCable Assembly To open the parts bag for that stageFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the Short Weight Tube On the bottomNylon Locknuts yet Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon JamnutsAssembly Bag for identification of the Pro Pulleys Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bracket onEd as shown Labeled Pulley BAGBracket On the back of the Butterfly Upright Identify the Rear Cable103 Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright Large tabsRemove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Pulley Direction shownBe removed in step Is attached as shownIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley Identify the Press Cable 72. It is approximately Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Pulley and the pin on the Press Top FrameTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PADChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down LEG LOW Pulley ARM Press Weight Resistance ChartHigh Press LEG Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No