Whirlpool MED / GD 9600S, MED / GD 9700S manual 12345included.12345467892649

Page 10

123456654172 12348941723

4

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

7

Flat-blade screwdriver

#2 Phillips screwdriver

Adjustable wrench that opens to 1" (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)

Wire stripper (direct wire installations)

Level

Vent clamps

Caulking gun and compound (for installing new exhaust vent)

Tin snips (new vent installations)

¼" nut driver (recommended)

Tape measure

Are you placing the dryer on a pedestal? You have the option of purchasing a pedestal separately for this dryer. You may select a 15.5" (39.4 cm) pedestal. This pedestal will add to the total height of the dryer for a total height of approximately 53.5" (135.9 cm).

For a garage installation, you will need to place the pedestal at least 3.5" (8.9 cm) abovethe7floor862. 446

Remove parts packages from dryer drum. Check that all parts are

12345included.12345467892649

Do not use leveling legs if installing the dryer on a pedestal.

Check local codes. Check existing electrical supply and venting. See “Electrical Requirements” and “Venting Requirements” before purchasing parts. 111111234

For close-clearance installations6276819between 31.5" (80.01 cm) and 37" (93.98 cm), see Plan Vent System section for venting requirements.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the Assistance or Service section of this manual.

To6789order, call the dealer from whom you purchased your dryer or refer to the Assistance or Service section of this manual.

White17WHP1500SQ

BlackWHP1500SB

3

Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the Assistance or Service section of this manual. Ask for Part Number 8541503.

2-1

Image 10

Contents Epic Forward Goals and ObjectivesTable of Contents Page Safety First GeneralModel Number Model & Serial Number DesignationsSerial Number Model & Serial Number Label Tech Sheet Locations Specifications 12345 14367389Purchased.9869374149893467762934899691241473393 12345included.12345467892649 1234546 527932759675445627927345 675794786 67846977 677 747276243454 12345678296745542764656457 5766377275 For a grounded, cord-connected dryer369#8 648 63#644568567 789123456Into a hook shape 42Connect the other wires to outer terminal block screws 33333333333 123456783933345678933743263747322374 6963747322374796 66466374732237427643764732237426263346 1232456728927383 3258412324 522932299662345678834962 12342 1473222 323439262534922625 5672541234563789 36969 759428 5632879766977%%6&997969 Component Locations Burner Gas Burner AssemblyFunnel Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch To remove the thermal fuse or ther- mistor On the nextTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the flame sensor To remove the high-limit thermostatComponent Testing HeaterDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests GAS Burner Coils Burner IgnitorFlame Sensor HIGH-LIMIT ThermostatDiagnostic Guide DiagnosticsElectrostatic Discharge ESD Sensitive Electronics Diagnostic Tests Display FAULT/ERROR CodesActivating The Diagnostic Test Mode Diagnostic Console switches and indica- tors Diagnostic Moisture SensorTroubleshooting Tests TroubleshootingTroubleshooting Guide Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Test #3 Heater Test Dryer does not heatHeat will not shut off Test #3a Thermistor TestTest #3b Thermal Fuse Test Test #3c GAS Valve Test GAS Dryers onlyTest #3c Thermal Cutoff Test Electric Dryers only Test #4 Moisture Sensor TestParticular group of LEDs does not light up E3 error code is displayedNone of the LEDs light up Single LED does not light upIf using an analog meter, the resis If using a digital meter, the resistanceChecking The Button Functions Test #6 Door Switch Test Checking The Rotary Cycle SelectorPage Wiring Diagrams Page Product Specifications Warranty Information Sources