Whirlpool MED / GD 9600S, MED / GD 9700S Component Locations, Burner Gas Burner Assembly, Funnel

Page 30

COMPONENT ACCESS

This section instructs you on how to service each component inside the Epic Front-Loading Gas and Electric Dryers. The components and their locations are shown below.

COMPONENT LOCATIONS

Drum Light

Electronic

Control

Board

User Interface

Drum Roller	Belt & Drum
Drum Roller
(1 of 4)

				Thermal Cutoff
Belt Switch (Mounted				(Electric Only)
Belt Switch (Mounted				(Electric Only)
On Drive Motor Bracket)				High-Limit Thermostat
				High-Limit Thermostat
Drive Motor
Thermal Fuse				Heater (Or Gas Burner)
Thermal Fuse
Thermistor				NOT SHOWN:
Thermistor				Door Switch &
				Door Switch &
				Moisture Sensor


			Burner				Gas Burner
			Burner				Assembly
	Flame		Funnel				Assembly
	Flame		Funnel
	Sensor
						Ignitor
						Ignitor
						High-Limit			Coil
						High-Limit
						Thermostat
						Thermostat			Assembly
									Assembly
										Gas
										Gas
										Regulator

4-1

Image 30

Contents Epic Forward Goals and ObjectivesTable of Contents Page Safety First GeneralModel & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Tech Sheet Locations Specifications 12345 14367389Purchased.9869374149893467762934899691241473393 12345included.12345467892649 1234546 527932759675445627927345 675794786 67846977 677 123456782967455427646 74727624345456457 5766377275 For a grounded, cord-connected dryer369#8 648 63#644568567 789123456Into a hook shape 42Connect the other wires to outer terminal block screws 33333333333 1234567839333456789336963747322374796 664663747322374 74326374732237427643764732237426263346 1232456728927383 3258412324 522932299662345678834962 12342 1473222 323439262534922625 5672541234563789 36969 759428 5632879766977%%6&997969 Burner Gas Burner Assembly Component LocationsFunnel Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch To remove the thermal fuse or ther- mistor On the nextTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the flame sensor To remove the high-limit thermostatComponent Testing HeaterDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests GAS Burner Coils Burner IgnitorFlame Sensor HIGH-LIMIT ThermostatDiagnostics Diagnostic GuideElectrostatic Discharge ESD Sensitive Electronics Display FAULT/ERROR Codes Diagnostic TestsActivating The Diagnostic Test Mode Diagnostic Console switches and indica- tors Diagnostic Moisture SensorTroubleshooting Tests TroubleshootingTroubleshooting Guide Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Test #3 Heater Test Dryer does not heatHeat will not shut off Test #3a Thermistor TestTest #3b Thermal Fuse Test Test #3c GAS Valve Test GAS Dryers onlyTest #3c Thermal Cutoff Test Electric Dryers only Test #4 Moisture Sensor TestParticular group of LEDs does not light up E3 error code is displayedNone of the LEDs light up Single LED does not light upIf using a digital meter, the resistance If using an analog meter, the resisChecking The Button Functions Test #6 Door Switch Test Checking The Rotary Cycle SelectorPage Wiring Diagrams Page Product Specifications Warranty Information Sources