Whirlpool MED / GD 9700S, MED / GD 9600S manual Removing the BELT, DRUM, & Rollers

Page 41

REMOVING THE BELT, DRUM, & ROLLERS

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug dryer or disconnect power.

2.Turn off gas supply to dryer.

3.Pull the dryer away from the wall and remove the top cover (see steps 4 and 5 on page 4-2 for the procedure).

4.Remove the console (see page 4-4 for the procedure).

5.Remove the lint duct (see steps 3 through 6 on page 4-7 for the procedure).

6.Reach around behind the drive motor and push the idler wheel arm to the left, then remove the tension, and remove the belt from the idler pulley.

Remove Belt

From Idler Pulley

7.Disconnect the 3-wire moisture sensor con- nector from the main harness connector.

Moisture Sensor

Connector

8.Disconnect the 3-wire door switch con- nector from the electronic control board connector.

3-Wire

Door Switch

Connector

9.Loosen the two top front panel screws.

Top Front Panel Screws

Push To Left

10. Remove the two bottom front panel screws.

Bottom Front Panel Screws

4-12

Image 41

Contents Epic Goals and Objectives ForwardTable of Contents Page General Safety FirstSerial Number Model & Serial Number DesignationsModel Number Model & Serial Number Label Tech Sheet Locations 12345 14367389 SpecificationsPurchased.9869374149893467762934899691241473393 12345included.12345467892649 527932759675445627927 1234546345 675794786 67846977 677 56457 123456782967455427646747276243454 For a grounded, cord-connected dryer 5766377275369#8 63#64456 648789123456 8567Into a hook shape 42Connect the other wires to outer terminal block screws 123456783933345678933 3333333333327643764732237426263346 6963747322374796 664663747322374743263747322374 32584 12324567289273835229322996 1232462345678834962 147 1234234922625 32343926253222 5672541234563789 428 75936969 5632879766977%%6&997969 Funnel Burner Gas Burner AssemblyComponent Locations Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch On the next To remove the thermal fuse or ther- mistorTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the high-limit thermostat To remove the flame sensorHeater Component TestingDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests Burner Ignitor GAS Burner CoilsHIGH-LIMIT Thermostat Flame SensorElectrostatic Discharge ESD Sensitive Electronics DiagnosticsDiagnostic Guide Activating The Diagnostic Test Mode Display FAULT/ERROR CodesDiagnostic Tests Diagnostic Moisture Sensor Diagnostic Console switches and indica- torsTroubleshooting Guide TroubleshootingTroubleshooting Tests Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Dryer does not heat Test #3 Heater TestTest #3a Thermistor Test Heat will not shut offTest #3c GAS Valve Test GAS Dryers only Test #3b Thermal Fuse TestTest #4 Moisture Sensor Test Test #3c Thermal Cutoff Test Electric Dryers onlyNone of the LEDs light up E3 error code is displayedParticular group of LEDs does not light up Single LED does not light upChecking The Button Functions If using a digital meter, the resistanceIf using an analog meter, the resis Checking The Rotary Cycle Selector Test #6 Door Switch TestPage Wiring Diagrams Page Product Specifications Warranty Information Sources