Whirlpool MED / GD 9700S, MED / GD 9600S manual To remove the burner assembly

Page 47

REMOVING THE BURNER ASSEMBLY,

FLAME SENSOR, AND HIGH-LIMIT THERMOSTAT

(GAS DRYERS ONLY)

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug dryer or disconnect power.

2.Turn off gas supply to dryer.

3.Remove the two hex-head screws from the bottom flange of the toe panel. Pull the panel out at the bottom, pull down, and remove the panel.

Burner Assembly

4.To remove the burner assembly:

a)Remove the two hex-head screws from the burner support bracket, and pull the bracket away from the burner assembly.

Screws
Screws		Burner Support

Toe Panel

Toe Panel Screws

4-18

Image 47

Contents Epic Goals and Objectives ForwardTable of Contents Page General Safety FirstSerial Number Model & Serial Number DesignationsModel Number Model & Serial Number Label Tech Sheet Locations 12345 14367389 SpecificationsPurchased.9869374149893467762934899691241473393 12345included.12345467892649 527932759675445627927 1234546345 675794786 67846977 677 56457 123456782967455427646747276243454 For a grounded, cord-connected dryer 5766377275369#8 63#64456 648789123456 8567Into a hook shape 42Connect the other wires to outer terminal block screws 123456783933345678933 3333333333327643764732237426263346 6963747322374796 664663747322374743263747322374 32584 12324567289273835229322996 1232462345678834962 147 12342567254 323439262534922625 32221234563789 5632 759428 36969879766977%%6&997969 Funnel Burner Gas Burner AssemblyComponent Locations Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch On the next To remove the thermal fuse or ther- mistorTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the high-limit thermostat To remove the flame sensorHeater Component TestingDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests Burner Ignitor GAS Burner CoilsHIGH-LIMIT Thermostat Flame SensorElectrostatic Discharge ESD Sensitive Electronics DiagnosticsDiagnostic Guide Activating The Diagnostic Test Mode Display FAULT/ERROR CodesDiagnostic Tests Diagnostic Moisture Sensor Diagnostic Console switches and indica- torsGas Dryers Only TroubleshootingTroubleshooting Guide Troubleshooting TestsElectric Dryers Only Test #2 Motor Circuit Test Dryer does not heat Test #3 Heater TestTest #3a Thermistor Test Heat will not shut offTest #3c GAS Valve Test GAS Dryers only Test #3b Thermal Fuse TestTest #4 Moisture Sensor Test Test #3c Thermal Cutoff Test Electric Dryers onlySingle LED does not light up E3 error code is displayedNone of the LEDs light up Particular group of LEDs does not light upChecking The Button Functions If using a digital meter, the resistanceIf using an analog meter, the resis Checking The Rotary Cycle Selector Test #6 Door Switch TestPage Wiring Diagrams Page Product Specifications Warranty Information Sources