Whirlpool MED / GD 9700S, MED / GD 9600S manual 8567, 789123456

#2"2#￿1232&'￿34567896￿856767￿$(2)57￿￿8￿￿￿776￿￿%￿31￿￿7￿￿￿￿￿￿￿￿$8￿￿￿￿￿5￿76￿￿￿579￿8￿7567￿￿￿￿6567￿￿588￿￿￿￿￿78976￿￿￿￿￿￿6￿￿￿￿!￿￿￿76￿￿76￿%￿6￿￿7655￿￿62￿￿￿886￿￿￿￿￿￿￿￿6￿￿5￿￿

12Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

#2"2123456732,￿*7#6'￿￿￿8567$579(2)￿￿￿￿￿￿￿77￿￿76%￿$8$￿￿￿￿￿￿￿￿￿765676￿76￿￿88￿￿￿7￿￿57968567976%89￿￿￿￿￿￿￿76%￿￿￿!67￿￿￿￿￿￿￿￿76￿+￿￿￿7￿

789123￿￿￿￿￿￿￿￿456 89￿￿68￿49￿￿7￿4568￿7345677

A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 1 1/2" (3.8 cm) from

3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

￿2Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw.

			￿￿8	￿31￿￿7￿￿￿￿￿￿85￿7￿￿			￿6￿￿7655￿￿6￿8￿86￿￿￿￿￿￿￿6￿￿5￿￿
32	Connect the other wires to outer terminal block screws.	#23456789￿￿6￿57		76$￿￿￿￿767￿￿6567		76%￿		2
42	Tighten screws.	"2#	8567￿	767￿￿8￿	￿567￿89	￿￿￿￿!￿￿￿76￿
5	Tighten strain relief screws.
	Insert tab of terminal block cover into slot of dryer rear panel.
6	Secure cover with hold-down screw.	32&'￿$(2)￿￿￿%￿￿￿￿￿￿￿56￿￿￿579￿8￿76￿￿6￿
	You have completed your electrical connection. Now go to
	“Venting Requirements.”

2-8