Whirlpool MED / GD 9600S, MED / GD 9700S manual Into a hook shape

Page 18

12Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.

$1232)2(6345677856757927676!"#7%7&767*856776876856776567!579976587897676'76677

32Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

42Squeeze hooked ends together. Tighten screws.

5Tighten strain relief screw.

Insert tab of terminal block cover into slot of dryer rear panel.

6Secure cover with hold-down screw.

You have completed your electrical connection. Now go to “Venting Requirements.”

78999123456789689499298999793657 7895

2(6579*56768567$1232).+&/98567!&76276!"#567!78896895*5956(3,157985576866-68&+-.

2Loosen or remove center silver-colored terminal block screw.

Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

$322(657934567898567276*!7%7&"#85657967!86856587767967676'76

12Connect the other wires to outer terminal block screws.

32Tighten screws.

4Tighten strain relief screws.

Insert tab of terminal block cover into slot of dryer rear panel.

5Secure cover with hold-down screw.

You have completed your electrical connection. Now go to “Venting Requirements.”

7899912345678968949929899974568 73456

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 31/2" (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires

into a hook shape.

1

2-9

Image 18

Contents Epic Forward Goals and ObjectivesTable of Contents Page Safety First GeneralModel & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Tech Sheet Locations Specifications 12345 14367389Purchased.9869374149893467762934899691241473393 12345included.12345467892649 1234546 527932759675445627927345 675794786 67846977 677 123456782967455427646 74727624345456457 5766377275 For a grounded, cord-connected dryer369#8 648 63#644568567 789123456Into a hook shape 42Connect the other wires to outer terminal block screws 33333333333 1234567839333456789336963747322374796 664663747322374 74326374732237427643764732237426263346 1232456728927383 3258412324 522932299662345678834962 12342 1473222 323439262534922625 5672541234563789 36969 759428 5632879766977%%6&997969 Burner Gas Burner Assembly Component LocationsFunnel Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch To remove the thermal fuse or ther- mistor On the nextTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the flame sensor To remove the high-limit thermostatComponent Testing HeaterDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests GAS Burner Coils Burner IgnitorFlame Sensor HIGH-LIMIT ThermostatDiagnostics Diagnostic GuideElectrostatic Discharge ESD Sensitive Electronics Display FAULT/ERROR Codes Diagnostic TestsActivating The Diagnostic Test Mode Diagnostic Console switches and indica- tors Diagnostic Moisture SensorTroubleshooting Tests TroubleshootingTroubleshooting Guide Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Test #3 Heater Test Dryer does not heatHeat will not shut off Test #3a Thermistor TestTest #3b Thermal Fuse Test Test #3c GAS Valve Test GAS Dryers onlyTest #3c Thermal Cutoff Test Electric Dryers only Test #4 Moisture Sensor TestParticular group of LEDs does not light up E3 error code is displayedNone of the LEDs light up Single LED does not light upIf using a digital meter, the resistance If using an analog meter, the resisChecking The Button Functions Test #6 Door Switch Test Checking The Rotary Cycle SelectorPage Wiring Diagrams Page Product Specifications Warranty Information Sources