Whirlpool MED / GD 9600S, MED / GD 9700S manual Manifold Clamp Screw

Page 48

b)Disconnect the following wires from the burner assembly:

Blue and white wires from the flame sensor terminals.

2-wire connector from the ignitor.

2-wire and 3-wire connectors from the coil assembly.

Flame Sensor

Wht & Blu Wires Coil Assembly 2-Wire Connector

3-Wire Connector

Ignitor Connector

c)Disconnect the gas line from the burner manifold at the right rear corner of the dryer.

d)Loosen the burner manifold clamp at the inside back of the dryer.

Manifold Clamp Screw

e)Remove the two hex-head screws from the burner mounting bracket, and pull the burner assembly out of the unit.

Bracket Screws

Burner Assembly

f)To remove the ignitor from the burner assembly, loosen the 5/16 inch hex- head screw, and remove the ignitor from the mounting bracket.

Ignitor Screw

Bracket

 

 

 

 

 

 

 

 

Continued on the next page.

4-19

Image 48
Contents Epic Forward Goals and ObjectivesTable of Contents Page Safety First GeneralModel & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Tech Sheet Locations Specifications 12345 14367389Purchased.9869374149893467762934899691241473393 12345included.12345467892649 1234546 527932759675445627927345 675794786 67846977 677 123456782967455427646 74727624345456457 5766377275 For a grounded, cord-connected dryer369#8 648 63#644568567 789123456Into a hook shape 42Connect the other wires to outer terminal block screws 33333333333 1234567839333456789336963747322374796 664663747322374 74326374732237427643764732237426263346 1232456728927383 3258412324 522932299662345678834962 12342 1473234392625 349226253222 5672541234563789 759 42836969 5632879766977%%6&997969 Burner Gas Burner Assembly Component LocationsFunnel Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch To remove the thermal fuse or ther- mistor On the nextTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the flame sensor To remove the high-limit thermostatComponent Testing HeaterDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests GAS Burner Coils Burner IgnitorFlame Sensor HIGH-LIMIT ThermostatDiagnostics Diagnostic GuideElectrostatic Discharge ESD Sensitive Electronics Display FAULT/ERROR Codes Diagnostic TestsActivating The Diagnostic Test Mode Diagnostic Console switches and indica- tors Diagnostic Moisture SensorTroubleshooting Troubleshooting GuideTroubleshooting Tests Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Test #3 Heater Test Dryer does not heatHeat will not shut off Test #3a Thermistor TestTest #3b Thermal Fuse Test Test #3c GAS Valve Test GAS Dryers onlyTest #3c Thermal Cutoff Test Electric Dryers only Test #4 Moisture Sensor TestE3 error code is displayed None of the LEDs light upParticular group of LEDs does not light up Single LED does not light upIf using a digital meter, the resistance If using an analog meter, the resisChecking The Button Functions Test #6 Door Switch Test Checking The Rotary Cycle SelectorPage Wiring Diagrams Page Product Specifications Warranty Information Sources