Whirlpool MED / GD 9700S, MED / GD 9600S manual 879766977%%6&997969

Page 29

1234567896￿￿￿8￿4

The Cycle End Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press and release the (ADJUSTABLE) CYCLE END SIGNAL to adjust the sound level or turn off the signal. Your dryer may vary from the model shown and may not have the same feature as shown12345here.

When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until the clothes are removed, or the Extra Care feature is finished.

￿￿2￿8￿ ￿￿3￿

The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry

36789￿7￿￿￿7￿￿￿￿￿￿7￿￿￿￿(for example, sweaters).

Do not remove the lint screen.

￿￿Open dryer door.

1234567839￿￿9

Place drying rack inside dryer drum, positioning the back wire on the ledge of the￿212inner￿95￿53￿￿￿￿3￿￿79￿dryer35￿￿￿3￿back567839panel￿￿9. Push down on front edge of drying rack to secure over the lint screen.

￿￿Put the wet items on top of the rack. Leave space between the items so air can reach all the surfaces.

123457Do not allow items to hang over the edge of the rack.

Close the door.

Select a Manual cycle, and choose a temperature or Air Only (see following chart). Items containing foam, rubber or plastic must be dried on a clothesline or by using the Air Only

￿￿￿￿7￿￿￿

￿￿￿￿￿￿3￿!"￿3￿!￿#

12345$66%7&￿￿￿￿￿9

Timed Low

60

temperature setting.

 

 

You must select a time by pressing the MANUAL DRY TIME (- or +) buttons. Reset time as needed to complete drying.

￿￿Refer to the following table.

Press (and hold) HOLD TO START button (about 1 second).

You must remove rack for normal tumbling. Do not use automatic cycles with the drying rack.

This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold.

Block to shape and lay flat on

Dry

 

the rack

 

￿￿￿￿￿￿8''￿￿7￿9766￿9￿7￿￿￿7"￿(%%6&9￿979￿6￿9

Timed

Low

60

Cotton or polyester fiber filled

Dry

 

 

 

 

 

 

 

 

 

 

Timed

Air Only

90

Foam rubber filled

Dry

(no

 

 

heat)

 

 

 

 

 

 

 

 

 

Timed

Air Only

90

 

Dry

(no

 

 

 

heat)

 

*(Minutes) Reset time to complete drying, if needed.

3-5

Image 29
Contents Epic Goals and Objectives ForwardTable of Contents Page General Safety FirstSerial Number Model & Serial Number DesignationsModel Number Model & Serial Number Label Tech Sheet Locations 12345 14367389 SpecificationsPurchased.9869374149893467762934899691241473393 12345included.12345467892649 527932759675445627927 1234546345 675794786 67846977 677 56457 123456782967455427646747276243454 For a grounded, cord-connected dryer 5766377275369#8 63#64456 648789123456 8567Into a hook shape 42Connect the other wires to outer terminal block screws 123456783933345678933 3333333333327643764732237426263346 6963747322374796 664663747322374743263747322374 32584 12324567289273835229322996 1232462345678834962 147 1234234922625 32343926253222 5672541234563789 428 75936969 5632879766977%%6&997969 Funnel Burner Gas Burner AssemblyComponent Locations Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch On the next To remove the thermal fuse or ther- mistorTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the high-limit thermostat To remove the flame sensorHeater Component TestingDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests Burner Ignitor GAS Burner CoilsHIGH-LIMIT Thermostat Flame SensorElectrostatic Discharge ESD Sensitive Electronics DiagnosticsDiagnostic Guide Activating The Diagnostic Test Mode Display FAULT/ERROR CodesDiagnostic Tests Diagnostic Moisture Sensor Diagnostic Console switches and indica- torsTroubleshooting Guide TroubleshootingTroubleshooting Tests Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Dryer does not heat Test #3 Heater TestTest #3a Thermistor Test Heat will not shut offTest #3c GAS Valve Test GAS Dryers only Test #3b Thermal Fuse TestTest #4 Moisture Sensor Test Test #3c Thermal Cutoff Test Electric Dryers onlyNone of the LEDs light up E3 error code is displayedParticular group of LEDs does not light up Single LED does not light upChecking The Button Functions If using a digital meter, the resistanceIf using an analog meter, the resis Checking The Rotary Cycle Selector Test #6 Door Switch TestPage Wiring Diagrams Page Product Specifications Warranty Information Sources