Whirlpool MED / GD 9600S, MED / GD 9700S manual 648, 63#64456

Page 16

1234567869￿￿5￿26￿￿￿56￿2￿￿￿￿6￿54￿5￿Unscrew the removable conduit connector and any screws from a / " (1. cm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads.

￿212￿345678946￿494￿6￿45￿￿￿8￿￿￿￿4￿￿4￿￿￿￿￿648￿￿￿8￿￿￿96￿6￿￿￿￿￿46￿￿64￿￿￿￿￿

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.

￿￿Now complete installation following instructions for your type of electrical connection:

￿￿￿￿￿5(recommended)

(if 4-wire is not available)

6￿45￿2￿￿￿￿46￿￿￿￿5￿2￿￿￿6￿￿￿63￿#￿6$￿%56$￿￿8

&63￿#6￿44'56

)￿62￿615￿2￿￿￿

 

￿￿

 

￿￿￿￿5￿2￿￿(62￿8

 

 

 

 

 

2345678

 

A UL listed,

4-wire connection:

4-wire receptacle

 

(NEMA Type 14-30R)

 

120/240 volt

Power supply cord

 

 

 

minimum,

 

 

 

 

30-amp, dryer

 

 

 

 

power supply

 

 

 

 

cord*

 

4-wire direct

 

A fused

4-wire connection:

 

 

 

disconnect or

Direct Wire

 

 

 

circuit breaker

 

 

 

 

box*

 

3-wire receptacle

 

A UL listed,

3-wire connection:

(NEMA type 10-30R)

 

120/240 volt

Power supply cord

 

 

 

minimum,

 

 

 

 

30-amp, dryer

 

 

 

 

power supply

 

 

 

 

cord*

 

3-wire direct

 

A fused

3-wire connection:

￿4678￿￿3

 

disconnect or

Direct Wire

 

 

 

circuit breaker

 

 

/ ￿

 

box*

 

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral wire, go to ?Optional 3-wire connection ? section.

￿￿￿￿￿￿!￿86123456789￿￿68￿49￿￿7￿93657￿￿￿￿￿￿7895￿7 A￿2*24!4￿￿￿8￿43)-￿￿￿￿￿wire6￿4connection￿5￿￿6￿￿￿￿/0￿￿8￿￿8￿￿44￿￿￿￿￿8￿￿￿￿4￿￿4￿￿!"#1is￿￿￿￿￿￿￿￿4￿￿4￿￿￿required￿$￿4￿%for￿￿&'3(mobile homes

and where local codes do not permit the use of -wire connections. )2"+,-%2. (￿￿￿

"￿7Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

2-7

Image 16
Contents Epic Forward Goals and ObjectivesTable of Contents Page Safety First GeneralModel Number Model & Serial Number DesignationsSerial Number Model & Serial Number Label Tech Sheet Locations Specifications 12345 14367389Purchased.9869374149893467762934899691241473393 12345included.12345467892649 1234546 527932759675445627927345 675794786 67846977 677 747276243454 12345678296745542764656457 5766377275 For a grounded, cord-connected dryer369#8 648 63#644568567 789123456Into a hook shape 42Connect the other wires to outer terminal block screws 33333333333 123456783933345678933743263747322374 6963747322374796 66466374732237427643764732237426263346 1232456728927383 3258412324 522932299662345678834962 12342 1473234392625 349226253222 5672541234563789 759 42836969 5632879766977%%6&997969 Component Locations Burner Gas Burner AssemblyFunnel Removing the Electronic Control Board Relay K1 P2 Removing the Console & Touchpad Subassembly Touchpad Subassembly Console Subpanel Catch Removing the Door Switch To remove the thermal fuse or ther- mistor On the nextTo remove the drive motor To remove the belt switch To remove the heater To remove the high-limit thermostat or the thermal cutoff Removing the BELT, DRUM, & Rollers To remove the belt and drum To remove a roller Removing the Drum Light Socket Squeeze Arms Removing the Moisture Sensor To remove the burner assembly Manifold Clamp Screw To remove the flame sensor To remove the high-limit thermostatComponent Testing HeaterDrive Motor Thermal Fuse Thermistor Thermal Cutoff Electric Dryers only Resistance Tests GAS Burner Coils Burner IgnitorFlame Sensor HIGH-LIMIT ThermostatDiagnostic Guide DiagnosticsElectrostatic Discharge ESD Sensitive Electronics Diagnostic Tests Display FAULT/ERROR CodesActivating The Diagnostic Test Mode Diagnostic Console switches and indica- tors Diagnostic Moisture SensorTroubleshooting Troubleshooting GuideTroubleshooting Tests Gas Dryers OnlyElectric Dryers Only Test #2 Motor Circuit Test Test #3 Heater Test Dryer does not heatHeat will not shut off Test #3a Thermistor TestTest #3b Thermal Fuse Test Test #3c GAS Valve Test GAS Dryers onlyTest #3c Thermal Cutoff Test Electric Dryers only Test #4 Moisture Sensor TestE3 error code is displayed None of the LEDs light upParticular group of LEDs does not light up Single LED does not light upIf using an analog meter, the resis If using a digital meter, the resistanceChecking The Button Functions Test #6 Door Switch Test Checking The Rotary Cycle SelectorPage Wiring Diagrams Page Product Specifications Warranty Information Sources