Miele T4819Ci operating instructions Programme duration / Estimated time remaining, Display shows

Page 15

Operating the tumble dryer

The display shows:

Programme duration

Programme stage Drying

Cooling down Finish

Check and fault messages

The following are also selected via the display:

Duration of the Warm air and Cool air programmes

Delay start

You can select a programme and set it to start at a later time.

The programme will start automatically once the delay start time has a elapsed.

Programmable functions

Default settings can be altered to adapt the dryer to different requirements. See "Programmable functions" at the end of this booklet for more details.

Perfect Dry indicator

The Perfect Dry system measures the residual content in the laundry in the sensor drying programmes to ensure perfect drying results.

After a programme has started, the electronics will estimate the duration of the programme (time remaining). The Perfect Dry indicator will flash while this is happening.

After a short while, the programme duration will appear in the display and the indicator will go out.

The Perfect Dry indicator will light up again when the selected drying level is reached and remain on until the programme is finished.

The Perfect Dry indicator does not light up during time controlled programmes: Woollens handcare, Cool air, Warm air, Gentle smoothing.

Programme duration / Estimated time remaining

The estimated duration (time remaining) will appear in the display.

The following factors all affect the estimated time remaining: residual moisture content after spinning; type of fabric; size of load; room temperature; fluctuations in power supply.

The electronics continually assess conditions in the dryer and adjust the estimated time remaining for a more accurate reading. Because of this, the time displayed can alter during the course of a programme.

Programmes can also finish earlier than expected, if, for example, particularly fine fabrics are being dried, the load is very small or items were partially dry beforehand.

15

Image 15
Contents Operating instructions For condenser tumble dryer T 4819 Ci Energy saving tips Caring for the environmentDisposal of the packing material Disposal of your old applianceContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Control panel Operating the tumble dryerProgramme duration / Estimated time remaining Display showsFollowing are also selected via the display Ironing Garment care label symbolsTips on drying DryingTurn on the tumble dryer How to dry correctlyBrief instructions Sort the laundrySelect any Extra options / Delay start Select a programmeDrying level programmes Start the programme Before the end of a programmeRemove the laundry at the end of the programme Extra options / Delay start Delay startExtra options Delicates Max. load 2 kg Normal, Hand iron Cottons Max. load 6 kg Extra dry, NormalHand iron, Machine iron Minimum iron Max. load 3 kg Normal, Hand ironProgramme chart Gentle smoothing Max. load 1 kg Shirts Max. load 2 kg Normal, Hand ironCool air Max. load 6 kg Warm air Max. load 6 kgAdding or removing laundry after a programme has started Altering Delay startChanging the programme sequence Once a programme has startedElectronic system lock To activate the lockTo deactivate the lock Emptying the condensed water container Cleaning and careCleaning them whilst dry Cleaning the fluff filtersCleaning them with water Cleaning the tumble dryer Removing the condenser unit Cleaning the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Check and fault messages Problem solving guideTo switch off this warning Problem Possible cause RemedyAirways indicator To switch off thisDisplay is dark Problem Possible cause Remedy Start/Stop button isProgramme indicator Flashing slowlyAn unsatisfactory drying result Goes on too long or Other problemsProblem Possible cause Remedy Drying process Even switches offDryer after Problem Possible cause Remedy Water leaks fromBeen cleaned Power cutChanging the lamp Optional accessories After Sales serviceFuture updates PC Appliance guaranteeFront view InstallationBuilding under a continous worktop / in a kitchen run Installation siteBefore moving the tumble dryer again e.g. when moving house Levelling the appliance Room ventilationWasher-dryer stack Removing the spacer bars Front panel dimensions Fitting the front panelFitting the front panel Fitting a door front panel made by another manufacturer Preparing the front panelWith spacer bars Without spacer bars Preparing the fixing points Plinth facing dimensions InstallationFitting a plinth facing External condensed water outlet General notesArranging the drain hose External drainage via a sink or gully Installation conditions requiring a non-return valveInstallation Non-rewireable plugs BS Electrical connectionElectrical connection U.K Woollens handcare Consumption dataTechnical data To check the setting Programmable functionsReduced residual moisture. Laundry drier Programmable functions Hours anti-crease factory default setting Anti-creaseAnti-crease off Hour anti-crease Normal buzzer Factory default setting Loud buzzer Altering the volume of the buzzerReduced residual moisture. Laundry drier Cooling down time extended by ten minutes Extending the cooling down timeFollow the steps ,, ... to programme and store in memory Factory default. Not in current programmeStandby OffFactory default setting. Not in current programme Memory function Memory deactivated factory default setting Memory activatedClean out airways indicator Keypad tone Factory default setting Adjusted for very soft water Adjusting the dryers electronics for very soft waterExtending the range of the drying levels Alteration rights reserved/0113 Nr 844 000