Miele T4819Ci operating instructions Levelling the appliance Room ventilation, Washer-dryer stack

Page 43

Installation

Levelling the appliance

Room ventilation

Turn the 4 screw feet to adjust the dryer to the correct height and level.

Longer screw feet are available as an optional accessory. Unscrew and remove the feet supplied with the appliance before fitting the longer screw feet.

The cover plate on the dryer must be aligned horizontally underneath the worktop.

The ventilation gaps in the plinth must not be covered over. This would hinder a sufficient flow of air to the dryer.

Air taken in for use in the drying process will be warm when it is expelled from underneath the dryer. This expelled air heats up the air in the room. It is therefore very important to ensure that the room is adequately ventilated, particularly if the dryer is located in a small room. Otherwise running times and energy consumption could be increased.

Washer-dryer stack

The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit (available to order) to match your dryer is required.

The stacking kit must be fitted by a suitably qualified fitter.

Before moving the tumble dryer again (e.g. when moving house)

After each use a small quantity of condensed water will collect in the area around the pump. This water can run out if the dryer is tipped up when it is being moved. It is therefore a good idea to run the Cool air programme for approximately 1 minute before moving it. Any remaining condensed water will then be fed into the condensed water container or out through the drain hose.

43

Image 43

Contents Operating instructions For condenser tumble dryer T 4819 Ci Energy saving tips Caring for the environmentDisposal of the packing material Disposal of your old applianceContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Control panel Operating the tumble dryerDisplay shows Programme duration / Estimated time remainingFollowing are also selected via the display Ironing Garment care label symbolsTips on drying DryingTurn on the tumble dryer How to dry correctlyBrief instructions Sort the laundrySelect a programme Select any Extra options / Delay startDrying level programmes Before the end of a programme Start the programmeRemove the laundry at the end of the programme Delay start Extra options / Delay startExtra options Delicates Max. load 2 kg Normal, Hand iron Cottons Max. load 6 kg Extra dry, NormalHand iron, Machine iron Minimum iron Max. load 3 kg Normal, Hand ironProgramme chart Gentle smoothing Max. load 1 kg Shirts Max. load 2 kg Normal, Hand ironCool air Max. load 6 kg Warm air Max. load 6 kgAdding or removing laundry after a programme has started Altering Delay startChanging the programme sequence Once a programme has startedTo activate the lock Electronic system lockTo deactivate the lock Emptying the condensed water container Cleaning and careCleaning them whilst dry Cleaning the fluff filtersCleaning them with water Cleaning the tumble dryer Removing the condenser unit Cleaning the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Check and fault messages Problem solving guideTo switch off this warning Problem Possible cause RemedyAirways indicator To switch off thisDisplay is dark Problem Possible cause Remedy Start/Stop button isProgramme indicator Flashing slowlyAn unsatisfactory drying result Goes on too long or Other problemsProblem Possible cause Remedy Drying process Even switches offDryer after Problem Possible cause Remedy Water leaks fromBeen cleaned Power cutChanging the lamp Optional accessories After Sales service Future updates PC Appliance guaranteeFront view InstallationBuilding under a continous worktop / in a kitchen run Installation siteLevelling the appliance Room ventilation Before moving the tumble dryer again e.g. when moving houseWasher-dryer stack Removing the spacer bars Fitting the front panel Front panel dimensionsFitting the front panel Preparing the front panel Fitting a door front panel made by another manufacturerWith spacer bars Without spacer bars Preparing the fixing points Installation Plinth facing dimensionsFitting a plinth facing General notes External condensed water outletArranging the drain hose External drainage via a sink or gully Installation conditions requiring a non-return valveInstallation Electrical connection Non-rewireable plugs BSElectrical connection U.K Woollens handcare Consumption dataTechnical data Programmable functions To check the settingReduced residual moisture. Laundry drier Programmable functions Anti-crease Hours anti-crease factory default settingAnti-crease off Hour anti-crease Normal buzzer Factory default setting Loud buzzer Altering the volume of the buzzerReduced residual moisture. Laundry drier Cooling down time extended by ten minutes Extending the cooling down timeFollow the steps ,, ... to programme and store in memory Factory default. Not in current programmeStandby OffFactory default setting. Not in current programme Memory function Memory deactivated factory default setting Memory activatedClean out airways indicator Keypad tone Factory default setting Adjusted for very soft water Adjusting the dryers electronics for very soft waterExtending the range of the drying levels Alteration rights reserved/0113 Nr 844 000