Miele T4819Ci operating instructions Removing the spacer bars

Page 44

Installation

Matching the fascia panel to the height of adjacent drawer fronts

The fascia panel can be aligned with the drawer fronts by adjusting the spacer bars.

Using a socket spanner, turn clockwise or anti-clockwise until the required height is reached.

If necessary individual bars can be removed or more added.

To do this, use the socket spanner to loosen the nuts.

An adapter kit with spacer bars and longer screws can be ordered as an optional accessory. This can be used to add spacer bars from below up to a maximum of 25 mm.

After fitting the bars, cut or pinch off any excess length from the screws.

Removing the spacer bars

All the spacer bars can be removed if the upper edge of the front panel needs to be flush with the upper edge of the appliance front directly underneath the fascia panel. See "Fitting a front panel made by another manufacturer".

Open the door.

Unscrew and remove the 3 screws (see arrows).

Remove all the spacer bars.

The 3 holes which are now free should be used to screw the front panel to the machine front later on.

44

Image 44

Contents Operating instructions For condenser tumble dryer T 4819 Ci Caring for the environment Disposal of the packing materialDisposal of your old appliance Energy saving tipsContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Operating the tumble dryer Control panelFollowing are also selected via the display Programme duration / Estimated time remainingDisplay shows Garment care label symbols Tips on dryingDrying IroningHow to dry correctly Brief instructionsSort the laundry Turn on the tumble dryerDrying level programmes Select any Extra options / Delay startSelect a programme Remove the laundry at the end of the programme Start the programmeBefore the end of a programme Extra options Extra options / Delay startDelay start Cottons Max. load 6 kg Extra dry, Normal Hand iron, Machine ironMinimum iron Max. load 3 kg Normal, Hand iron Delicates Max. load 2 kg Normal, Hand ironProgramme chart Shirts Max. load 2 kg Normal, Hand iron Cool air Max. load 6 kgWarm air Max. load 6 kg Gentle smoothing Max. load 1 kgAltering Delay start Changing the programme sequenceOnce a programme has started Adding or removing laundry after a programme has startedTo deactivate the lock Electronic system lockTo activate the lock Cleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Problem solving guide Check and fault messagesProblem Possible cause Remedy Airways indicatorTo switch off this To switch off this warningProblem Possible cause Remedy Start/Stop button is Programme indicatorFlashing slowly Display is darkAn unsatisfactory drying result Other problems Problem Possible cause Remedy Drying processEven switches off Goes on too long orProblem Possible cause Remedy Water leaks from Been cleanedPower cut Dryer afterChanging the lamp After Sales service Future updates PCAppliance guarantee Optional accessories Installation Front viewInstallation site Building under a continous worktop / in a kitchen runWasher-dryer stack Before moving the tumble dryer again e.g. when moving houseLevelling the appliance Room ventilation Removing the spacer bars Fitting the front panel Front panel dimensionsFitting the front panel With spacer bars Without spacer bars Fitting a door front panel made by another manufacturerPreparing the front panel Preparing the fixing points Fitting a plinth facing Plinth facing dimensionsInstallation Arranging the drain hose External condensed water outletGeneral notes Installation conditions requiring a non-return valve External drainage via a sink or gullyInstallation Electrical connection U.K Non-rewireable plugs BSElectrical connection Consumption data Woollens handcareTechnical data Reduced residual moisture. Laundry drier To check the settingProgrammable functions Programmable functions Anti-crease off Hour anti-crease Hours anti-crease factory default settingAnti-crease Altering the volume of the buzzer Normal buzzer Factory default setting Loud buzzerReduced residual moisture. Laundry drier Extending the cooling down time Cooling down time extended by ten minutesFactory default. Not in current programme StandbyOff Follow the steps ,, ... to programme and store in memoryFactory default setting. Not in current programme Memory deactivated factory default setting Memory activated Memory functionClean out airways indicator Keypad tone Adjusting the dryers electronics for very soft water Factory default setting Adjusted for very soft waterExtending the range of the drying levels Alteration rights reserved/0113 Nr 844 000