Miele T4819Ci Fitting a plinth facing, Plinth facing dimensions, Installation

Page 48

Installation

Fitting a plinth facing

The gap between the lower edge of the tumble dryer plinth and the floor can be closed up using a suitable kitchen furniture plinth facing.

The tumble dryer plinth has a special groove in which a plinth facing can be fitted.

Plinth facing dimensions

Length: 592 - 596 mm

Thickness: 8 mm

Height (H): The plinth facing height must be calculated after aligning the height of the appliance with the screw feet or after fitting the raising kit(s).

Installation

Calculate height (H) from the floor up into the groove (on the underside of the tumble dryer).

Cut the plinth facing to size.

Slide it into the groove.

Useful tip:

If the dryer is fitted on a raising kit, you can use double-sided adhesive tape on the back of the plinth facing to secure it to the raising kit.

48

Image 48

Contents Operating instructions For condenser tumble dryer T 4819 Ci Caring for the environment Disposal of the packing materialDisposal of your old appliance Energy saving tipsContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Operating the tumble dryer Control panelProgramme duration / Estimated time remaining Display showsFollowing are also selected via the display Garment care label symbols Tips on dryingDrying IroningHow to dry correctly Brief instructionsSort the laundry Turn on the tumble dryerSelect any Extra options / Delay start Select a programmeDrying level programmes Start the programme Before the end of a programmeRemove the laundry at the end of the programme Extra options / Delay start Delay startExtra options Cottons Max. load 6 kg Extra dry, Normal Hand iron, Machine ironMinimum iron Max. load 3 kg Normal, Hand iron Delicates Max. load 2 kg Normal, Hand ironProgramme chart Shirts Max. load 2 kg Normal, Hand iron Cool air Max. load 6 kgWarm air Max. load 6 kg Gentle smoothing Max. load 1 kgAltering Delay start Changing the programme sequenceOnce a programme has started Adding or removing laundry after a programme has startedElectronic system lock To activate the lockTo deactivate the lock Cleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Problem solving guide Check and fault messagesProblem Possible cause Remedy Airways indicatorTo switch off this To switch off this warningProblem Possible cause Remedy Start/Stop button is Programme indicatorFlashing slowly Display is darkAn unsatisfactory drying result Other problems Problem Possible cause Remedy Drying processEven switches off Goes on too long orProblem Possible cause Remedy Water leaks from Been cleanedPower cut Dryer afterChanging the lamp After Sales service Future updates PCAppliance guarantee Optional accessoriesInstallation Front viewInstallation site Building under a continous worktop / in a kitchen runBefore moving the tumble dryer again e.g. when moving house Levelling the appliance Room ventilationWasher-dryer stack Removing the spacer bars Front panel dimensions Fitting the front panelFitting the front panel Fitting a door front panel made by another manufacturer Preparing the front panelWith spacer bars Without spacer bars Preparing the fixing points Plinth facing dimensions InstallationFitting a plinth facing External condensed water outlet General notesArranging the drain hose Installation conditions requiring a non-return valve External drainage via a sink or gullyInstallation Non-rewireable plugs BS Electrical connectionElectrical connection U.K Consumption data Woollens handcareTechnical data To check the setting Programmable functionsReduced residual moisture. Laundry drier Programmable functions Hours anti-crease factory default setting Anti-creaseAnti-crease off Hour anti-crease Altering the volume of the buzzer Normal buzzer Factory default setting Loud buzzerReduced residual moisture. Laundry drier Extending the cooling down time Cooling down time extended by ten minutesFactory default. Not in current programme StandbyOff Follow the steps ,, ... to programme and store in memoryFactory default setting. Not in current programme Memory deactivated factory default setting Memory activated Memory functionClean out airways indicator Keypad tone Adjusting the dryers electronics for very soft water Factory default setting Adjusted for very soft waterExtending the range of the drying levels Alteration rights reserved/0113 Nr 844 000