Miele T4819Ci operating instructions Checking and cleaning the condenser unit housing

Page 32

Cleaning and care

￿Then flush the unit through from the front.

￿Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone.

￿Repeat as required.

￿Also make sure the rubber seals are clean.

The rubber seals must not be removed and must be free of kinks.

￿Shake the water off the condenser unit until no more droplets of water are visible.

Checking and cleaning the condenser unit housing

￿Remove any soiling still visible inside the housing unit by hand using a damp cloth. Do not try and access areas you cannot reach by hand!

Replacing the condenser unit

￿With the handle facing upwards, push the condenser unit back into position in its housing.

￿Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove.

When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove.

￿Replace the inner cover making sure the hooks locate correctly. Hold it at an angle and push it gently downwards.

￿Then turn the lever upwards into the horizontal position to lock the cover.

￿Replace the service panel and press the upper edge until it clicks into position.

￿It is important to ensure that both the condenser unit and the cover are correctly positioned and locked, otherwise water may leak from the dryer.

32

Image 32
Contents Operating instructions For condenser tumble dryer T 4819 Ci Caring for the environment Disposal of the packing materialDisposal of your old appliance Energy saving tipsContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Operating the tumble dryer Control panelFollowing are also selected via the display Programme duration / Estimated time remainingDisplay shows Garment care label symbols Tips on dryingDrying IroningHow to dry correctly Brief instructionsSort the laundry Turn on the tumble dryerDrying level programmes Select any Extra options / Delay startSelect a programme Remove the laundry at the end of the programme Start the programmeBefore the end of a programme Extra options Extra options / Delay startDelay start Cottons Max. load 6 kg Extra dry, Normal Hand iron, Machine ironMinimum iron Max. load 3 kg Normal, Hand iron Delicates Max. load 2 kg Normal, Hand ironProgramme chart Shirts Max. load 2 kg Normal, Hand iron Cool air Max. load 6 kgWarm air Max. load 6 kg Gentle smoothing Max. load 1 kgAltering Delay start Changing the programme sequenceOnce a programme has started Adding or removing laundry after a programme has startedTo deactivate the lock Electronic system lockTo activate the lock Cleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Problem solving guide Check and fault messagesProblem Possible cause Remedy Airways indicatorTo switch off this To switch off this warningProblem Possible cause Remedy Start/Stop button is Programme indicatorFlashing slowly Display is darkAn unsatisfactory drying result Other problems Problem Possible cause Remedy Drying processEven switches off Goes on too long orProblem Possible cause Remedy Water leaks from Been cleanedPower cut Dryer afterChanging the lamp After Sales service Future updates PCAppliance guarantee Optional accessoriesInstallation Front viewInstallation site Building under a continous worktop / in a kitchen runWasher-dryer stack Before moving the tumble dryer again e.g. when moving houseLevelling the appliance Room ventilation Removing the spacer bars Fitting the front panel Front panel dimensionsFitting the front panel With spacer bars Without spacer bars Fitting a door front panel made by another manufacturerPreparing the front panel Preparing the fixing points Fitting a plinth facing Plinth facing dimensionsInstallation Arranging the drain hose External condensed water outletGeneral notes Installation conditions requiring a non-return valve External drainage via a sink or gullyInstallation Electrical connection U.K Non-rewireable plugs BSElectrical connection Consumption data Woollens handcareTechnical data Reduced residual moisture. Laundry drier To check the settingProgrammable functions Programmable functions Anti-crease off Hour anti-crease Hours anti-crease factory default settingAnti-crease Altering the volume of the buzzer Normal buzzer Factory default setting Loud buzzerReduced residual moisture. Laundry drier Extending the cooling down time Cooling down time extended by ten minutesFactory default. Not in current programme StandbyOff Follow the steps ,, ... to programme and store in memoryFactory default setting. Not in current programme Memory deactivated factory default setting Memory activated Memory functionClean out airways indicator Keypad tone Adjusting the dryers electronics for very soft water Factory default setting Adjusted for very soft waterExtending the range of the drying levels Alteration rights reserved/0113 Nr 844 000