LG Electronics DLG1102W Installation test Duct check, Check the display for results, End of cycle

Page 27

INSTALLATION INSTRUCTIONS 27

Installation test (Duct check)

Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home.

•Your dryer features Flow SenseTM, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use.

NOTE

The dryer should be cool before starting this test. If the dryer was warmed up during installation, run the AIR DRY cycle for a few minutes to reduce the interior temperature.

To activate the installation test:

1.Remove the drying rack and literature, and then close the door.

Do not load anything in the drum for this test, as in may affect the accuracy of the results.

4.Check the display for results.

During the two minute test cycle, monitor the Flow SenseTM display on the control panel. If no bars are displayed, when the cycle ends, the exhaust system is adequate. If the exhaust system is severely restricted, the display will show four bars. Other problems may also be shown with error codes. Refer to the next page for error code details and solutions.

NO BARS:	FOUR BARS:
OK	RESTRICTED

Four bars indicates that the exhaust system is severely restricted. Have the system checked immediately, as performance will be poor.

5.End of cycle.

At the end of the test cycle, will display. The test cycle will end and the dryer will shut off automatically after a short delay.

ENGLISH

2.Press and hold the TEMP. CONTROL and OPTION buttons and then press the POWER button.

This button sequence activates the installation test. The code

will display if the activation is successful.

3.Press START/PAUSE button.

The dryer will start the test, which will last about two minutes. The heat will be turned on and the temperatures in the drum will be measured.

Image 27

Contents No El2001J DrYerSpecial Features Protocol P154Sanitization Performance of Residential Clothes dryer This is the safety alert symbol Important Safety InstructionsBasic Safety Precautions Safety Instructions for Installation Exhaust/Ducting Failure to do so can result in electric shock or injury Table of Contents Drying rack Sold separately Optional accessoriesIntroducing Your Dryer PartsControl panel features Custom Program Cycle Completion Indicator with Check Filter ReminderFlow Sense Duct Blockage Sensing System Indicator DisplayPress and hold Installation InstructionsPreview installation order Leveling the dryerSee Venting the dryer Installation location requirementsSide of the dryer. See Connecting electric dryers ClearancesLeveling the dryer Recommended installation spacing for cabinet installationReversing the door Hinge screwSwing Door Adapter Duct Bracket Knockout Installing the side vent kitOption 1 Side Venting Option 2 Bottom VentingVenting the dryer Routing and Connecting Ductwork Correct VentingIncorrect Venting Connect the dryer to the type of gas shown on the nameplate Connecting gas dryersElectrical requirements for gas models only Failure to do so can result in fire, explosion, or deathConnecting the gas supply High-altitude installationsElectrical connection Electrical requirements for electric models only Connecting electric dryersConnecting electric dryers cont. USA only Four-wire connection for electric dryers Power cordUL-Listed Wire Power Cord Use UL-listed4-wire #10 AWG-minimum copper conductor cable Four-wire connection for electric dryers Direct wireThree-wire connection for electric dryers Power cord Use UL-listed3-wire #10 AWG-minimum copper conductor cable Three-wire connection for electric dryers Direct wireGas dryer must be permanently attached to the floor Final installation checkGAS Models Electric ModelsPress START/PAUSE button Installation test Duct checkCheck the display for results End of cycleCheck the duct condition Restricted or blocked airflowTE1 or tE2 PS or PF or nPBegin Cycle Operating the dryer3TURN on the Dryer Select a CycleCertified by NSF Cycle guideSensor dry cycles Manual dry cyclesSorting load Loading the dryerCheck the lint filter before every load To Save a Custom Program Cycle setting buttons Special functionsCustom program To Add Cycle Options to a CycleRegular cleaning MaintenanceBefore calling for service TroubleshootingSpecifications Smartdiagnosis Using SmartdiagnosistmWarranty Period HOW Service is Handled Page Secadora Panel DE Control Fácil Para Usar Características EspecialesEstas palabras significan Instrucciones Importantes DE SeguridadNo altere los controles Instrucciones DE Conexión a Tierra Instrucciones Importantes parapara la instalación Guarde Estas Instrucciones Tabla de contenidos Partes Accesorios opcionalesSecado en parrilla Adquirido por separado Pantalla DE Tiempo Y Estado Características del panel de controlBotones DE MÁS TIEMPO/MENOS Tiempo More TIME/LESS Time Programa Botón CyclesPrograma Personalizado Custom Program PantallaEstimated Time Remaining Recordatorio DE Verificar Filtro Check Filter ReminderInstrucciones Para LA Instalación Vista previa del orden de instalaciónPulse y mantenga Exterior. Consulte Requisitos de ventilación Requisitos del lugar de instalaciónEspacios de instalación Un lugar que permita la instalación correcta del sistema deNivelación de la secadora Inversion de la puerta Codo 11/2 Instalación del kit de ventilación lateralOpción 1 Ventilación lateral Opción 2 Ventilación inferiorCónexión del conducto de ventilación de la secadora Incorrecta Conexión del conducto de ventilación de la secadoraVentilación de escape CorrectaRequisitos eléctricos para modelos a gas únicamente Conexión de secadoras a gasConector flexible de acero Conexión del suministro de gasConexión eléctrica Instalaciones en lugares de gran altitudRequisitos eléctricos únicamente para modelos eléctricos Cómo conectar las secadoras eléctricas cont. Sólo EE.UU Se requiere un protector de tensión listado por UL Cómo conectar las secadoras eléctricasNeutro Negro Haga los finales de los 3 cables en forma de gancho Revisión de instalación final Modelos a GASModelos Eléctricos Pulse el botón INICIO/PAUSASTART/PAUSE Test de Instalación conducto de comprobarObserve la pantalla para conocer el resultado Fin del cicloCompruebe las condiciones del conducto Flujo de aire restringido o bloqueadoTE1 o tE2 PS o PF o nPSeleccionar UN Ciclo Cómo UsarFuncionamiento de la secadora Encender LA SecadoraCertificado por NSF Guía de ciclosCiclos de secado con sensor sensor dry Ciclos de secado manual manual dryClasificación de cargas Revise el filtro de pelusa antes de cada usoCómo cargar la secadora Botones de ajuste de ciclos Funciones especialesPrograma personalizado Limpieza regular MantenimientoAntes de llamar a mantenimiento ResoluciÓn de problemasEspecificaciones Utilización del SmartDiagnosis Más cercano Período DE Garantía Cómo SE Administra EL MantenimientoMantenimiento en el hogar In-Home Llame al 1-800-243-0000 y escoja la opción adecuadaPage Español Page Español Canada