Maytag W10222378A SecuretheDrainHose, PlanVentSystem, Recommended exhaust installations

Page 14

SecuretheDrainHose

1.Move the washer/dryer to its final location and remove any cardboard used to move the washer/dryer.

2.Locate the remaining piece of shipping strap. See “Remove Shipping Strap.”

Shipping strap

3.Wrap the drain hose to the laundry tub leg or standpipe with the shipping strap (A or B below). Push fastener into the nearest hole in the shipping strap (see illustration above).

ABC

If the water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the shipping strap around the water inlet hoses and the drain hose (C above). Push fastener into the nearest hole in the shipping strap (see illustration above).

PlanVentSystem

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible.

A

D

 

 

E

 

F

B

 

 

G

C

H

A. Dryer

E. Elbow

B. Rigid metal or flexible metal vent

F. Clamps

C. Clamps

G. Elbow

D. Wall

H. Exhaust hood

Optional exhaust installations

This washer/dryer can be converted to exhaust out the right or left side. To convert the washer/dryer, use Side Exhaust Kit Part Number 279823. If your washer/dryer was previously exhausted from the right or left side, it can be converted to rear exhaust by using standard offset connections. To cover the hole in the side, one of the following plugs can be added:

692790 (white)

3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from the dealer from whom you purchased your washer/dryer.

ABC

A. Standard rear offset exhaust installation

B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown. Refer to the manufacturer’s instructions provided with the vent system.

ABC

A. Loop system with standard elbows

B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [51 mm] clearance)

NOTE: The following kits for close clearance alternate installations are available for purchase. Please reference the “Assistance or Service” section of the Washer/Dryer User Instructions.

Over-the-Top Installation:

Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 mm) to 18" (457 mm) mismatch

Part Number 4396011 - 18" (457 mm) to 29" (737 mm) mismatch

Part Number 4396014 - 29" (737 mm) to 50" (1.27 m) mismatch

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents LAVEUSE/SÉCHEUSE Électrique DE 27 69 CM ToolsandParts AlternatePartsWasher/Dryer Dimensions Installation ClearancesMobile Home Additional Installation Requirements Location RequirementsDrainSystem ElectricalRequirements- U.S.AIf your outlet looks like this If connecting by direct wireElectricalRequirements-Canada Sections into the hole below the terminal block opening so Electrical Connection -U.S.A. OnlyUL marking on strain relief. Put the tabs of the two clamp Hold in place. Tighten strain relief screw enough to holdStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire Remove center silver-colored terminal block screwConnect neutral wire white or center wire of power supply Block. Tighten screwPage VentingRequirements Vent materialRemoveShippingStrap Install LevelingLegsInstall the front leveling feet ConnecttheDrainHoseConnect the Inlet Hoses Alternate installations for close clearances Recommended exhaust installationsOptional exhaust installations SecuretheDrainHoseVent system chart InstallVentSystemSpecial provisions for mobile home installations Level Washer/DryerIf the dryer will not start, check the following Complete InstallationCheck that you have all of your tools Sécurité DE LA LAVEUSE/SÉCHEUSE Pièces nécessaires pour la laveuse non fournies OutillageetpiècesPièces fournies Outillage requisIl vous faudra Exigences d’emplacementAutres pièces Si vous avez Vous devrez acheter’installation dans une maison mobile exige Installation dans une maison mobile autres exigencesDimensions de la laveuse/sécheuse Système devidangeSystème de vidange par le plancher illustration D Spécifications électriques CanadaSystème de vidange avec évier de buanderie illustration C ’est à l’utilisateur qu’incombe la responsabilité deExigences concernant l’évacuation Matériel pour l’évacuationÉvacuation Les styles de clapets recommandés sont illustrés ci-dessousEnlever la sangle d’expédition Le clapet incliné illustré ici est acceptableRaccordement des tuyaux d’alimentation Installation des pieds de nivellementRaccordement du tuyaude vidange Connecter les tuyaux d’alimentation à la laveuse Immobilisationdu tuyau de vidangeNettoyer les conduites d’eau Pour un placard ou un endroit exiguAutres installations où le dégagement est réduit Installations d’évacuation recommandéesInstallations d’évacuation facultatives Planification du système d’évacuationTableau des systèmes d’évacuation Installation du système d’évacuationNivellement de la laveuse/sécheuse Déterminer l’itinéraire d’acheminement du conduitSi la sécheuse ne démarre pas, vérifier ce qui suit Acheverl’installationRaccordement du conduit d’évacuation Page Page Page W10222378A Tous droits réservés
Top Page Image Contents