Maytag W10222378A Style 2 Direct wire strain relief, Wire connection Power supply cord

Page 7

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any screws from a 34" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads.

A

B

C

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.

Electrical Connection Options

If your home has:

And you will be

Go to Section

 

connecting to:

 

4-wire receptacle

A UL listed,

4-wire connection:

(NEMA Type 14-30R)

120/240 volt

Power supply cord

 

minimum,

 

 

 

30-amp, dryer

 

 

power supply

 

 

cord*

 

4-wire direct

A fused

4-wire connection:

 

disconnect or

Direct Wire

 

circuit breaker

 

 

5"

box*

 

(127 mm)

 

 

3-wire receptacle

A UL listed,

3-wire connection:

(NEMA type 10-30R)

120/240 volt

Power supply cord

 

minimum,

 

 

 

30-amp, dryer

 

 

power supply

 

 

cord*

 

3-wire direct

A fused

3-wire connection:

 

disconnect or

Direct Wire

 

circuit breaker

 

 

312"

box*

 

 

 

(89 mm)

 

 

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral wire, go to “Optional 3-wire connection” section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for all mobile homes and where local codes do not permit the use of 3-wire connections.

BF A

C D EG

A. 4-wire receptacle (NEMA type 14-30R)

B.4-prong plug

C.Ground prong

D.Neutral prong

E. Spade terminals with upturned ends F. 34" (19 mm) UL listed strain relief

G.Ring terminals

4.Now complete installation following instructions for your type of electrical connection:

4-wire(recommended)

3-wire(if 4-wire is not available)

7

Image 7
Contents LAVEUSE/SÉCHEUSE Électrique DE 27 69 CM AlternateParts ToolsandPartsLocation Requirements Installation ClearancesMobile Home Additional Installation Requirements Washer/Dryer DimensionsElectricalRequirements- U.S.A DrainSystemElectricalRequirements-Canada If connecting by direct wireIf your outlet looks like this Hold in place. Tighten strain relief screw enough to hold Electrical Connection -U.S.A. OnlyUL marking on strain relief. Put the tabs of the two clamp Sections into the hole below the terminal block opening soWire connection Power supply cord Style 2 Direct wire strain reliefRemove center silver-colored terminal block screw Wire connection Direct WireBlock. Tighten screw Connect neutral wire white or center wire of power supplyPage Vent material VentingRequirementsConnecttheDrainHose Install LevelingLegsInstall the front leveling feet RemoveShippingStrapConnect the Inlet Hoses SecuretheDrainHose Recommended exhaust installationsOptional exhaust installations Alternate installations for close clearancesLevel Washer/Dryer InstallVentSystemSpecial provisions for mobile home installations Vent system chartCheck that you have all of your tools Complete InstallationIf the dryer will not start, check the following Sécurité DE LA LAVEUSE/SÉCHEUSE Outillage requis OutillageetpiècesPièces fournies Pièces nécessaires pour la laveuse non fourniesSi vous avez Vous devrez acheter Exigences d’emplacementAutres pièces Il vous faudraSystème devidange Installation dans une maison mobile autres exigencesDimensions de la laveuse/sécheuse ’installation dans une maison mobile exige’est à l’utilisateur qu’incombe la responsabilité de Spécifications électriques CanadaSystème de vidange avec évier de buanderie illustration C Système de vidange par le plancher illustration DMatériel pour l’évacuation Exigences concernant l’évacuationLe clapet incliné illustré ici est acceptable Les styles de clapets recommandés sont illustrés ci-dessousEnlever la sangle d’expédition ÉvacuationRaccordement du tuyaude vidange Installation des pieds de nivellementRaccordement des tuyaux d’alimentation Pour un placard ou un endroit exigu Immobilisationdu tuyau de vidangeNettoyer les conduites d’eau Connecter les tuyaux d’alimentation à la laveusePlanification du système d’évacuation Installations d’évacuation recommandéesInstallations d’évacuation facultatives Autres installations où le dégagement est réduitDéterminer l’itinéraire d’acheminement du conduit Installation du système d’évacuationNivellement de la laveuse/sécheuse Tableau des systèmes d’évacuationRaccordement du conduit d’évacuation Acheverl’installationSi la sécheuse ne démarre pas, vérifier ce qui suit Page Page Page Tous droits réservés W10222378A