Maytag W10222378A installation instructions DrainSystem, ElectricalRequirements- U.S.A

Page 4

Mobile home installations require:

Metal exhaust system hardware, which is available for purchase from your dealer.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

DrainSystem

The washer/dryer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Alternate Parts.”

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of

2" (51 mm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (51 mm) diameter to 1" (25 mm) diameter standpipe adapter kit is available. See “Alternate Parts.”

The top of the standpipe must be at least 39" (991 mm) high and no higher than 96" (2.4 m) from the bottom of the washer.

39"

(991 mm)

AB

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (864 mm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See “Alternate Parts.”

The siphon break must be a minimum of 28" (711 mm) from the bottom of the washer. Additional hoses might be needed.

34" (864 mm)

CD

ElectricalRequirements- U.S.A.

It is your responsibility

To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your washer/dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the internal ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

If local codes do not permit the connection of a neutral ground wire to the neutral wire, see “Optional 3-wire connection” in the “Electrical Connection - U.S.A. Only” section.

A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations,

(2)mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

A UL listed strain relief.

4

Image 4
Contents LAVEUSE/SÉCHEUSE Électrique DE 27 69 CM ToolsandParts AlternatePartsInstallation Clearances Mobile Home Additional Installation RequirementsWasher/Dryer Dimensions Location RequirementsDrainSystem ElectricalRequirements- U.S.AElectricalRequirements-Canada If connecting by direct wireIf your outlet looks like this Electrical Connection -U.S.A. Only UL marking on strain relief. Put the tabs of the two clampSections into the hole below the terminal block opening so Hold in place. Tighten strain relief screw enough to holdStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire Remove center silver-colored terminal block screwConnect neutral wire white or center wire of power supply Block. Tighten screwPage VentingRequirements Vent materialInstall LevelingLegs Install the front leveling feetRemoveShippingStrap ConnecttheDrainHoseConnect the Inlet Hoses Recommended exhaust installations Optional exhaust installationsAlternate installations for close clearances SecuretheDrainHoseInstallVentSystem Special provisions for mobile home installationsVent system chart Level Washer/DryerCheck that you have all of your tools Complete InstallationIf the dryer will not start, check the following Sécurité DE LA LAVEUSE/SÉCHEUSE Outillageetpièces Pièces fourniesPièces nécessaires pour la laveuse non fournies Outillage requisExigences d’emplacement Autres piècesIl vous faudra Si vous avez Vous devrez acheterInstallation dans une maison mobile autres exigences Dimensions de la laveuse/sécheuse’installation dans une maison mobile exige Système devidangeSpécifications électriques Canada Système de vidange avec évier de buanderie illustration CSystème de vidange par le plancher illustration D ’est à l’utilisateur qu’incombe la responsabilité deExigences concernant l’évacuation Matériel pour l’évacuationLes styles de clapets recommandés sont illustrés ci-dessous Enlever la sangle d’expéditionÉvacuation Le clapet incliné illustré ici est acceptableRaccordement du tuyaude vidange Installation des pieds de nivellementRaccordement des tuyaux d’alimentation Immobilisationdu tuyau de vidange Nettoyer les conduites d’eauConnecter les tuyaux d’alimentation à la laveuse Pour un placard ou un endroit exiguInstallations d’évacuation recommandées Installations d’évacuation facultativesAutres installations où le dégagement est réduit Planification du système d’évacuationInstallation du système d’évacuation Nivellement de la laveuse/sécheuseTableau des systèmes d’évacuation Déterminer l’itinéraire d’acheminement du conduitRaccordement du conduit d’évacuation Acheverl’installationSi la sécheuse ne démarre pas, vérifier ce qui suit Page Page Page W10222378A Tous droits réservés