Bosch Appliances Nexxt Series manual Useful Tools, Installation location, Install Dryer

7

Checklist for Installation

1. Unpack the dryer.

Useful Tools

The following tools are helpful during installation:

1.T20 star head screwdriver

2.Philips screwdriver (#2)

3.Flat blade screwdriver

4.Open end wrench 1 in. (25mm)

5.Bubble level

supplied

by the

appropriate

Install the

dryer and level side to

side

ductwork

parts

manufacturers

(see and front to back. Use a bubble level.

page

14)

Never remove

the heightcadjustable

feet!

i

If space

is very

restricted,

it

is

recommended to fit

the

initial

parts 13.

Connect

the exhaust

duct

to

the

of the exhaust

duct

to

the

dryer

exhaust

air

outlet on

the

dryer (see

page

13).

before the dryer is moved to

its

final

installation

location.

14.

Insert

the

dryer electrical

plug

into

11.

Move

the dryer

to

its

final

location.

the wall receptacle (see page

9).

15.

Read

the

operating instructions

to

NOTICE

understand

how your

dryer

operates.

(see page

16).

Do not slide dryer across the floor if heightcadjustable feet have been extended. Feet and/or dryer base may be damaged if dryer is slid across floor with heightcadjustable feet extended.

12. Position and then level the dryer.

16.Conduct an appliance test:

q Check	that	the	drum is empty.
q Close	the	dryer	door.
q Switch	the	dryer	to "Extra	Dry"
and then press the •Start"
button.
q After 3-5 minutes press the
Stop button and			open the	door.

q If the interior of the dryer feels warm, the dryer has been connected properly.

Switch the dryer to "OFF".

q If the dryer does not work, switch the dryer to "OFF". Look in the troubleshooting section (page 25) and find the fault.

Installation location

2.Remove all objects from the drum.

3.

Check

the

dryer for visible

d WARNING

4.

damage.

DO

NOT

install the

dryer:

Position

the

dryer

near

the

-

outdoors

installation

location

(see page 7).

-

in an environment with dripping

5.

If

required,

change

the

door

hinge

water,

to

the

left

(see page 15).

-

near

flammable

materials,

6.

If

required,

install the side

or

The

dryer

should

be

level

with

all

four

-

in

rooms

which

are

at risk

of

frost

feet

firmly

on the

ground.

The

dryer

-

in

rooms

which

may

contain

gas

bottom

exhaust air

outlet

on

the

must

not

wobble.

If the

dryer is not

level

or

other

fuels,

dryer

(see

page 15).

or

if

it does

wobble,

the

feet

must

be-

in

cupboards

with

lockable

doors

7.

Have

the

power supply

cord

fitted adjusted.

Adjust the

heightcadjustable

or

in

alcoves.

by

a

qualified technician

or a

feet

until

the

dryer

does

not rock

and is

licensed

electrician

(see

page

9).

level,

both frontctocback

and

The installation room must be well

ventilated, otherwise the dryer will

8.

Check

for

•Y" connection,

short

sidectocside.

operate

below optimum

performance.



hose

and

AQUASTOP Hose

q

After

making

preliminary

Do not operate the dryer at

included with the dryer packaging

adjustments, press down on each

temperatures

above

104F° (40C)°

or

(see page

8).

corner

of

the

dryer

to

make

sure

below

41F°

(5C)° .

Low

temperatures

9.

Connect

the

water

supply

to

the

the unit

does

not

wobble.

If

it

does

wobble, lower

the

foot

on

that

affect the automatic program sequence

back

of

the

dryer

(see

page

8

for

and may prolong the drying times.

corner

until the

foot

touches the

detailed

instructions).

The installation surface for the dryer

floor firmly.

10.

Install

exhaust ductwork

if

must be

clean, level

and

firm.

Do

not

install

the

appliance

on

carpets!

necessary.

Compensate for uneven floors with the

Follow

the

installation instructions

heightcadjustable

feet.