Maytag W10150622A Stopping, Pausing or Restarting, Drying and Cycle Tips, To restart the dryer

Page 21

Turn the knob to desired Sensor Dry Cycle.

Select DRYNESS to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level.

The default dryness setting is Normal when a Sensor Dry Cycle is selected. You can select a different dryness level, depending on your load, by pressing Dryness and choosing More, Less or Damp. Selecting More, Less or Damp automatically adjusts the sensed time needed. Once a dryness level is set, it cannot be changed without stopping the cycle.

Select the desired Options.

To make changes during a Sensor Dry Cycle:

Press PAUSE/CANCEL.

Adjust Dryness.

NOTE: Dryness selections can be made only while using Sensor Dry Cycles.

How the Sensi-Care™ Drying System Works

Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast the load is drying, how hot the air should be and when clothes are dry. The system automatically stops the cycle to help save time and avoid overdrying.

To use a Timed Cycle

Turn knob to desired Timed Cycle.

Press the TIMED CYCLE ADJUST up or down arrows until the desired drying time is displayed. Press the up or down arrows and the time will change by 1-minute intervals. Press and hold the up or down arrows and the time will change by 5-minute intervals.

NOTE: The Timed Cycle Adjust features can be used only with Timed Cycles.

Press TEMP until the desired temperature illuminates.

NOTE: The Temp feature can be used only with Timed Cycles.

NOTE: During a Timed Cycle, you can change the settings for Time, Temp, the Wrinkle Prevent setting and the End of Cycle Signal.

5.(OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”

6.(OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A signal will sound to alert you when a cycle ends. For more details, see “End of Cycle Signal.”

7.Press START. Be sure the door is closed.

If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEL twice.

Stopping, Pausing or Restarting

To stop or pause your dryer at any time

Open the door or press PAUSE/CANCEL once. Press PAUSE/CANCEL twice to cancel a cycle.

To restart the dryer

Close the door. Press START until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your load. If a Sensor Dry Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

21

Image 21
Contents W10150622A Sécheuse ÉlectriqueTable DES Matières Table of ContentsYour safety and the safety of others are very important Dryer SafetyInstallation Instructions Tools and PartsLocation Requirements Electrical Requirements U.S.A. Only If your outlet looks like this If connecting by direct wireElectrical Requirements Canada Only Power Supply Cord Direct Wire Style 1 Power supply cord strain reliefElectrical Connection U.S.A. Only Style 2 Direct wire strain relief Wire connection Direct Wire Wire connection Power Supply Cord12.7 BDE CG F Optional 3-wire connection If using an existing vent system Venting RequirementsIf this is a new vent system Vent material Clamps Plan Vent SystemAlternate installations for close clearances Install Vent SystemVent system chart Special provisions for mobile home installationsInstall Leveling Legs Connect VentLevel Dryer Reinstall the door Remove the door assemblyReverse Door Swing Reverse the strikeU.S.A Complete InstallationCanada If the dryer will not start, check the followingTo use a Sensor Dry Cycle Press Power Dryer USEStarting Your Dryer Drying and Cycle Tips Stopping, Pausing or RestartingTo stop or pause your dryer at any time To restart the dryerCycles Status LightsModifiers End of Cycle Signal OptionsChanging Cycles, Modifiers Options Drying Rack Option Changing the Preset Dryness Level SettingsChanging Modifiers and Options after pressing Start To use the drying rackCleaning the Lint Screen Cleaning the Dryer LocationCleaning the Dryer Interior Dryer CareVacation and Moving Care TroubleshootingChanging the Drum Light Dryer OperationDryer Results Unusual soundsDryer displaying code message Lint on load Cycle time too shortStains on load or drum Loads are wrinkledAccessories Assistance or ServiceU.S.A CanadaONE Year Limited Warranty Maytag Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA SécheuseOutillage et pièces Instructions D’INSTALLATIONPièces fournies Pièces nécessairesDimensions de la sécheuse Exigences d’emplacementIl vous faudra Dégagements de séparation à respecter’est à l’utilisateur qu’incombe la responsabilité de Linstallation dans une maison mobile exigeExigences concernant lévacuation En cas dutilisation du système dévacuation existantEn cas de nouveau système dévacuation Planification du système d’évacuation Brides de serrageÉvacuation Autres installations où le dégagement est réduit Déterminer litinéraire dacheminement du conduitTableau des systèmes dévacuation Installation des pieds de nivellement Installation du système d’évacuationRaccordement du conduit d’évacuation Réglage de laplomb de la sécheuseInversion du sens douverture de la porte Dépose de la porteInversion de la gâche Réinstallation de la porte Si la sécheuse ne démarre pas, vérifier ce qui suit Achever linstallationMise en marche de la sécheuse Utilisation DE LA SécheuseArrêt, pause ou remise en marche Pour mettre la sécheuse en pause ou larrêter à tout momentPour remettre la sécheuse en marche Témoins lumineux Conseils pour le séchage et les programmesProgrammes Modificateurs Signal de fin de programme Signal de fin de programmeDamp Dry Chime sonnerie indiquant un séchage humide Changement des programmes après avoir appuyé sur StartUtilisation de la grille de séchage Option de grille de séchageSéchage sur grille Réglage Temp Durée Chandails en laine Jouets rembourrés ou oreillersEntretien DE LA Sécheuse Nettoyage de lemplacement de la sécheuseNettoyage du filtre à charpie Nettoyage de l’intérieur de la sécheuseRetrait de la charpie accumulée DéménagementChangement de l’ampoule d’éclairage Du tambour Fonctionnement de la sécheuse DépannageAbsence de chaleur Sons inhabituelsRésultats de la sécheuse La sécheuse est-elle installée dans un placard?Temps de programme trop court Le filtre à charpie est-il obstrué de charpie?Assistance OU Service AccessoiresAu Canada Garantie DES Gros Appareils Ménagers Maytag Corporation W10150622A SP PN W10150623A