Maytag W10150639A manual Stopping Your Dryer, Pausing or Restarting, Control Locked, Status Lights

Page 19

Press TEMP until the desired temperature illuminates.

NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.

Press the EXTRA CARE feature button if this option is desired.

Press the CYCLE END SIGNAL button to set volume to desired level.

Press and hold HOLD TO START button until dryer starts (about 1 second).

While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.

Stopping Your Dryer

To stop your dryer at any time

Press OFF twice or open the door.

Pausing or Restarting

To pause the dryer at any time

Open the door or press OFF once.

To restart the dryer

Close the door and press and hold HOLD TO START button until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is running:

Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control Locked status light is on.

When the dryer is off, it is not necessary to press the Control On button before activating the Control Locked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but can’t be restarted until the control is unlocked.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle.

Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package instructions.

Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits and synthetic fabrics.

Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of lighter fabrics, leading to increased shrinking or wrinkling.

Cycle tips

Dry most loads using the preset cycle settings.

Refer to the Automatic or Manual Preset Cycle Settings chart (in the “Cycles” section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or LESS.

If you wish to adjust the cycle length of a Manual Cycle, you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual Cycles.

Status Lights

You may follow the progress of your dryer with the drying status indicator lights.

Sensing

When a cycle is first turned on, the Sensing light illuminates until a wet item is detected.

In an Automatic Cycle, if a wet item has not been detected within 10 minutes, the Sensing light will turn off and the dryer will shut down.

In a Manual Cycle, if a wet item is not detected after 10 minutes the Wet light turns on and the selected cycle continues.

Wet

The Wet light will turn on when a wet item has been detected in the dryer. The Wet light will remain on until:

The damp dry point is reached in an Automatic Cycle.

The dryer enters the cool down period in a Manual Cycle.

19

Image 19
Contents W10150638A Sécheuse À GAZTable DES Matières Table of ContentsYour safety and the safety of others are very important Dryer SafetyImportant Safety Instructions Tools and Parts Installation InstructionsOptional Pedestal Location Requirements Installation clearancesDryer Dimensions Custom undercounter installation Dryer onlyCabinet are required Recommended installation spacing for cabinet installationCloset installation Dryer only Recessed or closet installation Dryer on pedestalRequired spacing Mobile home Additional installation requirementsMobile home installations require Electrical RequirementsBurner input requirements Gas Supply RequirementsGas Type Gas supply lineDryer gas pipe Gas supply pressure testingIf using an existing vent system Venting RequirementsExhaust Optional exhaust installationsPlan Vent System ClampsSpecial provisions for mobile home installations Alternate installations for close clearancesDetermine vent path Make Gas Connection Install Vent SystemInstall Leveling Legs Vent system chartRemove the door Level DryerReverse Door Swing Connect VentReverse the hinge and hinge bracket Reinstalling the doorStyle 1 Remove the plug strip Complete InstallationStyle 2 Remove the label If the dryer will not start, check the following Dryer USETo use a Manual Cycle Starting Your DryerTo use an Automatic Cycle How Automatic Cycles WorkDrying and Cycle Tips Pausing or RestartingStopping Your Dryer Control LockedCycles Drying Rack Additional FeaturesDyer Care Cleaning the Dryer LocationCleaning the Lint Screen Every load cleaningChanging the Drum Light Cleaning the Dryer InteriorRemoving Accumulated Lint Vacation and Moving CareDryer Operation TroubleshootingDryer Results Loads are wrinkled Cycle time too shortLint on load Stains on load or drumCanada Assistance or ServiceAccessories U.S.AONE Year Limited Warranty Maytag Corporation Major Appliance WarrantyPage Votre sécurité et celle des autres est très importante Sécurité DE LA SécheuseImportantes Instructions DE Sécurité Outillage et pièces Instructions D’INSTALLATIONPiédestal facultatif Dégagements de séparation à respecter Exigences d’emplacementDimensions de la sécheuse Il vous faudraInstallation dans un placard Sécheuse seulement Espacement recommandé pour linstallation dans un placard’entrée d’air au sommet du placard Spécifications électriques Linstallation dans une maison mobile exigeExigences concernant le raccordement au gaz Type de gazCanalisation d’arrivée de gaz Gaz naturelEn cas dutilisation du système dévacuation existant Exigences concernant lévacuationCaractéristiques d’alimentation du brûleur Canalisation d’arrivée de gaz de la sécheuseBrides de serrage Conduit métallique rigideConduit métallique flexible CoudesAutres installations où le dégagement est réduit Installations d’évacuation facultativesPlanification du système d’évacuation Tableau des systèmes dévacuation Installation du système d’évacuationInstallation des pieds de nivellement Déterminer litinéraire dacheminement du conduitUtilisation dans une maison mobile Raccordement au gazEnlever la porte Raccordement du conduit d’évacuationMise à niveau de la sécheuse Inversion du sens douverture de la porteInverser la charnière et son support Réinstallation de la porteStyle 2 Retirer l’étiquette Si la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationMise en marche de la sécheuse Utilisation DE LA SécheuseUtilisation dun programme automatique Pour mettre la sécheuse en pause à nimporte quel moment Arrêt de la sécheusePause ou remise en marche Pour arrêter la sécheuse à n’importe quel momentConseils pour le séchage et les programmes Verrouillage des commandesTémoins lumineux Programmes Caractéristiques supplémentaires Grille de séchage Cycle End Signal signal de fin de programmeUtilisation de la grille de séchage Nettoyage à chaque charge Nettoyage de lemplacement de la sécheuseEntretien DE LA Sécheuse Nettoyage du filtre à charpieChangement de l’ampoule d’éclairage Du tambour Nettoyage de l’intérieur de la sécheuseRetrait de la charpie accumulée DéménagementFonctionnement de la sécheuse DépannageRésultats de la sécheuse Charges froissées Temps de programme trop courtCharpie sur la charge Taches sur la charge ou sur le tambourSi vous avez besoin de pièces de rechange Assistance OU ServiceAccessoires Au CanadaGarantie DES Gros Appareils Ménagers Maytag Corporation Tous droits réservés W10150638A SP PN W10150639A