Furuno SC-50 manual Mast diameter Separation distance minimum, Antenna and field of view

Page 11

2.INSTALLATION

The horizontal separation between the antenna and masts must be as follows:

Mast diameter

Separation distance (minimum)

10 cm

1.5 m

30 cm

3 m

SC-50’s antenna

Horizontal separation distance

Mast, etc.

Horizontal separation between antenna and masts

The field of view above the antenna should be as shown below, ±80° against zenith. To avoid reflections from masts and the like, locate the antenna well away from the shadows of the radar mast, etc.

Zenith

-80￿+80￿

SC-series antenna

SIDE VIEW

Antenna and field of view

Referring to the illustration below, locate the antenna away from objects which might block reception, such as a mast.

Mast, etc.

Less than 10￿

TOP VIEW

Locate the antenna unit above the radar antenna, out of the radar beam.

SC-series Antenna

Radar Antenna

2-2

Image 11
Contents Satellite Compass Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingWord to the Owner of the SC-50 FeaturesForeword System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListStandard supply Optional equipment Principle of Operation This page intentionally left blank Antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumHorizontal separation between antenna and masts Display unit, processor unit Example of antenna installed below superstructuresAntenna unit SC-303 Installing the Antenna UnitsMounting dimensions for antenna, orienting the antenna Cable from antenna No. marked on cable Waterproofing the antenna connectorHow to fasten the antenna cable Coating bolt, nut and washers with silicone sealantAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsAntenna unit SC-603 MountingFixing antenna unit to pedestal Orienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableProcessor unit orientation, deck mounting Installing the Processor UnitDeck, bulkhead mount Installation of processor unit on the underside of a desk Installation on the underside of a deskFlush mount F Installing the Display UnitDesktop, overhead mounting Flush mountFlush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Processor unit, rear view WiringGeneral wiring diagram Sectional view of coaxial cable 3D2V How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBMain menu Initial SettingsInstallation setup menu Confirming satellite status choosing mounting methodSatellite tracking status display Heading setup menuChoosing heading source Processor unit, cover opened General wiringConnection of External Equipment Cable Sectional view, fabrication Fabrication of cablesDisplay unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Nav data display Choosing a DisplayDescription of displays Heading displayROT Rate-of-Turn display Steering displayCompass display Set and drift display, speed and distance run display Set and Drift display, Distance Run displayBuzzer options Dgps Alarm SetupAlarm menu Dgps alarm optionsSatellite status display Confirming Satellite StatusGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Baud rate options Data OUT1 menu, sentencesHeading talker options Tx interval optionsIEC, Nmea version options Log pulse options Log pulseGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode Waas Search options WAAS/DGPS SetupPosition fix mode options WAAS/DGPS menuAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Restoration options HDG Backup optionsOthers Menu Others menuTrip menu Trip MenuReset Distance prompt Resetting Distance RunThis page intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingSymptom Cause Remedy TroubleshootingTroubleshooting Test start prompt DiagnosticsDiagnostic test1 Test menu optionsPush KEY Diagnostic test sequenceTEST2 display Diagnostic test2Alarm options Diagnostic test3Prompts for erasure of data Program NumberClearing Data Program version no. displayPrompt for turning off the power Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryMessage display Replacement of FuseError Messages Error Message Meaning RemedyData ERR Error messages con’t from previousAP-1 AppendixMenu Tree AP-2 SC-50 SpecificationsFuruno IN-1 IndexPacking List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page