Furuno SC-50 manual How to insert the cable cover, Antenna unit

Page 15

2INSTALLATION

8.Set the “cable cover” to the antenna base as shown in the figure below.

Cable Cover

How to insert the cable cover

HOW TO REMOVE CABLE COVER

Insert slotted-head screwdriver here to remove cable cover.

9.Attach nine “bird-repellent fixtures” (supplied) to the antenna cover as shown below. Use the paper pattern to position the fixtures.

Bird-repellent fixture

N

U

R

F

U

 

Paper pattern

Antenna unit

2-6

Image 15
Contents Satellite Compass Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingFeatures ForewordWord to the Owner of the SC-50 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListStandard supply Optional equipmentPrinciple of Operation This page intentionally left blank Installation Mounting ConsiderationsAntenna unit Mast diameter Separation distance minimum Horizontal separation between antenna and mastsAntenna and field of view Display unit, processor unit Example of antenna installed below superstructuresInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaAntenna unit SC-303 Cable from antenna No. marked on cable Waterproofing the antenna connectorHow to fasten the antenna cable Coating bolt, nut and washers with silicone sealantAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsAntenna unit SC-603 MountingFixing antenna unit to pedestal Orienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableInstalling the Processor Unit Deck, bulkhead mountProcessor unit orientation, deck mounting Installation of processor unit on the underside of a desk Installation on the underside of a deskFlush mount F Installing the Display UnitDesktop, overhead mounting Flush mountFlush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring General wiring diagramProcessor unit, rear view Sectional view of coaxial cable 3D2V How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBMain menu Initial SettingsInstallation setup menu Confirming satellite status choosing mounting methodHeading setup menu Choosing heading sourceSatellite tracking status display General wiring Connection of External EquipmentProcessor unit, cover opened Cable Sectional view, fabrication Fabrication of cablesOperation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Nav data display Choosing a DisplayDescription of displays Heading displaySteering display Compass displayROT Rate-of-Turn display Set and drift display, speed and distance run display Set and Drift display, Distance Run displayBuzzer options Dgps Alarm SetupAlarm menu Dgps alarm optionsSatellite status display Confirming Satellite StatusGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Baud rate options Data OUT1 menu, sentencesTx interval options IEC, Nmea version optionsHeading talker options Log pulse options Log pulseSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode Waas Search options WAAS/DGPS SetupPosition fix mode options WAAS/DGPS menuProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation HDG Restoration options HDG Backup optionsOthers Menu Others menuTrip menu Trip MenuReset Distance prompt Resetting Distance RunThis page intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingTroubleshooting TroubleshootingSymptom Cause Remedy Test start prompt DiagnosticsDiagnostic test1 Test menu optionsPush KEY Diagnostic test sequenceTEST2 display Diagnostic test2Alarm options Diagnostic test3Prompts for erasure of data Program NumberClearing Data Program version no. displayPrompt for turning off the power Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryMessage display Replacement of FuseError Messages Error Message Meaning RemedyData ERR Error messages con’t from previousAppendix Menu TreeAP-1 AP-2 SC-50 SpecificationsFuruno IN-1 IndexPacking List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page