Furuno SC-50 manual Wiring, General wiring diagram, Processor unit, rear view

Page 25

2. INSTALLATION

2.5Wiring

This section covers general wiring. For further details see the interconnection diagram at the back of this manual.

ANTENNA UNIT	ANTENNA UNIT
ANTENNA UNIT	SC-603
SC-303
	OR
	3

PROCESSOR UNIT

SC-501

TPPX6-3D2V-15M, 15m

DPYC 1.5

(or equivalent)

12-24 VDC

MJ-A7SPF0006-100, 10m

DISPLAY UNIT

SC-502

*

General wiring diagram

	GPS ANT
1	2	3

DISPLAY

ANTENNA Terminals			DISPLAY Connector	Ground Terminal
Ant. Elem. 1	(No Color): GPS ANT1		Connect cable from	Connect ground wire
Ant. Elem. 2	(Yellow):	GPS ANT2	display unit here.	between ground
Ant. Elem. 3	(Red):	GPS ANT2		terminal and
				ship’s grounding bus.

Processor unit, rear view

2-16

Image 25

Contents Satellite Compass Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingForeword FeaturesWord to the Owner of the SC-50 System configuration System ConfigurationStandard supply Equipment ListOptional equipment Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Mounting Considerations InstallationAntenna unit Horizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Display unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsAntenna unit SC-303 How to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsMounting Antenna unit SC-603Fixing antenna unit to pedestal Orienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableDeck, bulkhead mount Installing the Processor UnitProcessor unit orientation, deck mounting Installation of processor unit on the underside of a desk Installation on the underside of a deskDesktop, overhead mounting Installing the Display UnitFlush mount Flush mount FFlush mount S kit Type OP20-17, Code No Flush mount SFlush mount S General wiring diagram WiringProcessor unit, rear view Sectional view of coaxial cable 3D2V How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuChoosing heading source Heading setup menuSatellite tracking status display Connection of External Equipment General wiringProcessor unit, cover opened Cable Sectional view, fabrication Fabrication of cablesControls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and drift display, speed and distance run display Set and Drift display, Distance Run displayAlarm menu Dgps Alarm SetupDgps alarm options Buzzer optionsSatellite status display Confirming Satellite StatusDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Baud rate options Data OUT1 menu, sentencesIEC, Nmea version options Tx interval optionsHeading talker options Log pulse options Log pulseSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode Position fix mode options WAAS/DGPS SetupWAAS/DGPS menu Waas Search optionsGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation Others Menu HDG Backup optionsOthers menu HDG Restoration optionsTrip menu Trip MenuReset Distance prompt Resetting Distance RunThis page intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostic test1 DiagnosticsTest menu options Test start promptPush KEY Diagnostic test sequenceTEST2 display Diagnostic test2Alarm options Diagnostic test3Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryPrompt for exchanging battery Prompt for turning off the powerError Messages Replacement of FuseError Message Meaning Remedy Message displayData ERR Error messages con’t from previousMenu Tree AppendixAP-1 AP-2 SC-50 SpecificationsFuruno IN-1 IndexＰａｃｋｉｎｇＬｉｓｔ SC-501-J/E SC-303 工事材料表 Installation Materials ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page