Furuno SC-50 manual Iii, MAINTENANCE, Troubleshooting

Page 4

3.10

WAAS/DGPS Setup

3-16

3.11

OTHERS Menu

3-19

3.12

TRIP Menu

3-20

3.13

Resetting Distance Run

3-21

4 MAINTENANCE, TROUBLESHOOTING

................................................................4-1

4.1

Preventive Maintenance

4-1

4.2

Troubleshooting

4-2

4.3

Diagnostics

4-3

4.4

Program Number

4-7

4.5

Clearing Data

4-7

4.6

Replacement of Battery

4-8

4.7

Replacement of Fuse

4-9

4.8

Error Messages

4-9

APPENDIX

AP-1

SPECIFICATIONS

SP-1

INDEX

...........................................................................................................................

4-1

iii

Image 4
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiForeword FeaturesWord to the Owner of the SC-50 System Configuration System configurationEquipment List Standard supplyOptional equipment Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Mounting Considerations InstallationAntenna unit Horizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsAntenna unit SC-303 Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitHow to orient the antenna elements Antenna unit SC-603Mounting Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementDeck, bulkhead mount Installing the Processor UnitProcessor unit orientation, deck mounting Installation on the underside of a desk Installation of processor unit on the underside of a deskInstalling the Display Unit Desktop, overhead mountingFlush mount Flush mount FFlush mount S kit Type OP20-17, Code No Flush mount SFlush mount S General wiring diagram WiringProcessor unit, rear view How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuChoosing heading source Heading setup menuSatellite tracking status display Connection of External Equipment General wiringProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationControls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Choosing a Display Description of displaysHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps Alarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Data OUT1 menu, sentences Baud rate optionsIEC, Nmea version options Tx interval optionsHeading talker options Log pulse Log pulse optionsSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation HDG Backup options Others MenuOthers menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRMenu Tree AppendixAP-1 AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page