Furuno SC-50 manual Program Number, Clearing Data, Program version no. display

Page 60

4. MAINTENANCE, TROUBLESHOOTING

4.4Program Number

You may display the program number as follows:

1.Press the [MENU] key to open the menu.

2.Choose SOFT VER. and then press the [ENT] key.

SOFTWARE VERSION

DISPLAY

205-1341-**.**

PROCESS

205-1342-**.**

GPS1

4850263-*.**

GPS2

4850263-*.**

GPS3

4850263-*.**

** = Program version no.

Program version no. display

3. Press the [DISP] key to close the program version no. display.

4.5Clearing Data

You may clear GPS data and system data all at once or individually as follows:

1.Press the [MENU] key to open the menu.

2.Choose ERASE and then press the [ENT] key.

3.Choose GPS DATA, SYSTEM DATA or ALL BACKUP DATA (clears GPS and SYSTEM data) as appropriate. One of the following displays appears depending on your selection.

ERASE GPS DATA?

ARE YOU SURE?

YES NO

ERASE SYSTEM DATA? (DEFAULT)

ARE YOU SURE?

YES NO

ERASE ALL BACKUP DATA? (DEFAULT)

ARE YOU SURE?

YES NO

Prompts for erasure of data

4.Press to choose YES and then press the [ENT] key to erase. After data is erased the message “Completed erasing. Turn off the unit.” Is displayed.

Note: MOUNTING, DIRECTION and LANGUAGE in the INST menu, HDG RESTORATION and HDG BACKUP in the OTHERS menu and OFFSET in the HEADING SETUP menu are not cleared.

5. Turn off and on the power.

4-7

Image 60
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures ForewordWord to the Owner of the SC-50 System Configuration System configurationEquipment List Standard supplyOptional equipment Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Installation Mounting ConsiderationsAntenna unit Mast diameter Separation distance minimum Horizontal separation between antenna and mastsAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaAntenna unit SC-303 Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitHow to orient the antenna elements Antenna unit SC-603Mounting Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementInstalling the Processor Unit Deck, bulkhead mountProcessor unit orientation, deck mounting Installation on the underside of a desk Installation of processor unit on the underside of a deskInstalling the Display Unit Desktop, overhead mountingFlush mount Flush mount FFlush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring General wiring diagramProcessor unit, rear view How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuHeading setup menu Choosing heading sourceSatellite tracking status display General wiring Connection of External EquipmentProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationOperation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps Alarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Data OUT1 menu, sentences Baud rate optionsTx interval options IEC, Nmea version optionsHeading talker options Log pulse Log pulse optionsSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation HDG Backup options Others MenuOthers menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRAppendix Menu TreeAP-1 AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page