Furuno SC-50 manual Safety Instructions

Page 2

SAFETY INSTRUCTIONS

Safety Instructions for the Operator

 

Safety Instructions for the Installer

 

 

 

 

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment.

Only qualified personnel should work inside the equipment.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire.

Continued use can cause fatal damage to the equipment. Contact a FURUNO agent for service.

Do not place liquid-filled containers on the top of the processor unit.

Fire or electrical shock may result if the liquid enters the equipment.

Use the proper fuse.

Use of a wrong fuse can damage the equipment and cause fire.

WARNING

Turn off the power at the switchboard before beginning the installation.

Fire or electrical shock can result if the power is left on.

Do not install the equipment where it may get wet from rain or water splash.

Water in the equipment can cause fire, electrical shock or damage to the equipment.

NOTICE

Observe the following compass safe distances to prevent interference to a magnetic compass:

 

Standard

Steering

 

Compass

Compass

Display unit

0.5 m

0.3 m

SC-502

 

 

Processor unit

1.3 m

0.8 m

SC-501

 

 

Antenna unit

0.3 m

0.3 m

SC-303

 

 

Antenna unit

0.3 m

0.3 m

SC-603

 

 

CAUTION

No one navigation device should ever be solely replied upon for the navigation of a vessel.

Always confirm position against all avail- able aids to navigation (incl. nautical charts), for safety of vessel and crew.

WARNING LABEL

A warning label is attached to the processor unit. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer about replacement.

WARNING

WARNING LABEL

Name:

Warning Label (1)

To avoid electrical shock, do not

remove cover. No user-serviceable

Type:

86-003-1011-0

parts inside.

 

 

Code No.: 100-236-230

i

Image 2
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiWord to the Owner of the SC-50 FeaturesForeword System Configuration System configurationOptional equipment Equipment ListStandard supply Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumHorizontal separation between antenna and masts Example of antenna installed below superstructures Display unit, processor unitAntenna unit SC-303 Installing the Antenna UnitsMounting dimensions for antenna, orienting the antenna Coating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitMounting How to orient the antenna elementsAntenna unit SC-603 Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementProcessor unit orientation, deck mounting Installing the Processor UnitDeck, bulkhead mount Installation on the underside of a desk Installation of processor unit on the underside of a deskFlush mount Installing the Display UnitDesktop, overhead mounting Flush mount FFlush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Processor unit, rear view WiringGeneral wiring diagram How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuSatellite tracking status display Heading setup menuChoosing heading source Processor unit, cover opened General wiringConnection of External Equipment Fabrication of cables Cable Sectional view, fabricationDisplay unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps alarm options Dgps Alarm SetupAlarm menu Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Data OUT1 menu, sentences Baud rate optionsHeading talker options Tx interval optionsIEC, Nmea version options Log pulse Log pulse optionsGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode WAAS/DGPS menu WAAS/DGPS SetupPosition fix mode options Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation Others menu HDG Backup optionsOthers Menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceSymptom Cause Remedy TroubleshootingTroubleshooting Test menu options DiagnosticsDiagnostic test1 Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram version no. display Program NumberClearing Data Prompts for erasure of dataPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Prompt for turning off the powerError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Data ERRAP-1 AppendixMenu Tree AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page