Furuno SC-50 manual Demonstration mode

Page 46

3. OPERATION

3.9.5Demonstration mode

The demonstration mode provides simulated operation of the equipment.

1.Press the [MENU] key to open the menu.

2.Choose SYS SETUP and then press the [ENT] key.

3.Choose DEMO and then press the [ENT] key.

4.Choose ON or OFF as appropriate and then press the [ENT] key.

5.Press the [DISP] key to close the menu.

The indication SIM appears at the top of the screen when the demonstration mode is active. When the demonstration mode is first made active, SIMULATION MODE appears when the power is turned on and it is erased when any key is pressed.

3-15

Image 46
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiForeword FeaturesWord to the Owner of the SC-50 System Configuration System configurationOptional equipment Equipment ListStandard supply Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Mounting Considerations InstallationAntenna unit Horizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsAntenna unit SC-303 Coating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitMounting How to orient the antenna elementsAntenna unit SC-603 Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementDeck, bulkhead mount Installing the Processor UnitProcessor unit orientation, deck mounting Installation on the underside of a desk Installation of processor unit on the underside of a deskFlush mount Installing the Display UnitDesktop, overhead mounting Flush mount FFlush mount S kit Type OP20-17, Code No Flush mount SFlush mount S General wiring diagram WiringProcessor unit, rear view How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuChoosing heading source Heading setup menuSatellite tracking status display Connection of External Equipment General wiringProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationControls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps alarm options Dgps Alarm SetupAlarm menu Buzzer optionsConfirming Satellite Status Satellite status displayDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Data OUT1 menu, sentences Baud rate optionsIEC, Nmea version options Tx interval optionsHeading talker options Log pulse Log pulse optionsSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode WAAS/DGPS menu WAAS/DGPS SetupPosition fix mode options Waas Search optionsGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation Others menu HDG Backup optionsOthers Menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Test menu options DiagnosticsDiagnostic test1 Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram version no. display Program NumberClearing Data Prompts for erasure of dataPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Prompt for turning off the powerError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Data ERRMenu Tree AppendixAP-1 AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page