Furuno SC-50 manual Geodetic data, System Setup menu

Page 44

3. OPERATION

3.9System Setup

3.9.1Geodetic data

Your unit is preprogrammed to recognize most of the major chart systems of the world. Although the WGS-84 system (default setting) is the GPS standard, other categories of charts in other datum still exist. Match the GPS datum with the chart system you use.

1.Press the [MENU] key to open the menu.

2.Choose SYS SETUP and then press the [ENT] key.

SYSTEM SETUP

DATUM

:

WGS84

UNITS

: kt

TIME DIFF

: +00:00

TIME DISP

: 24 HOUR

TEST?

 

 

DEMO

: OFF

EXCHANGE BATTERY?

SYSTEM SETUP menu

3.Confirm that the cursor is selecting DATUM and then press the [ENT] key.

4.Choose WGS84 (GPS standard), WGS72 or OTHER according to the nautical chart you use and then press the [ENT] key.

5.If you chose WGS72 or WGS84, press the [DISP] key to finish. For OTHER, go to step 6.

6 Press the [ENT] key.

7.Use the Omnipad to enter chart number, referring to the geodetic chart list on page A-2. Choose location with or ; change value with ▲ or ▼.

8.Press the [ENT] key.

9.Press the [DISP] key to close the menu.

3-13

Image 44
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiWord to the Owner of the SC-50 FeaturesForeword System Configuration System configurationEquipment List Standard supplyOptional equipment Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumHorizontal separation between antenna and masts Example of antenna installed below superstructures Display unit, processor unitAntenna unit SC-303 Installing the Antenna UnitsMounting dimensions for antenna, orienting the antenna Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitHow to orient the antenna elements Antenna unit SC-603Mounting Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementProcessor unit orientation, deck mounting Installing the Processor UnitDeck, bulkhead mount Installation on the underside of a desk Installation of processor unit on the underside of a deskInstalling the Display Unit Desktop, overhead mountingFlush mount Flush mount FFlush mount S Flush mount SFlush mount S kit Type OP20-17, Code No Processor unit, rear view WiringGeneral wiring diagram How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuSatellite tracking status display Heading setup menuChoosing heading source Processor unit, cover opened General wiringConnection of External Equipment Fabrication of cables Cable Sectional view, fabricationDisplay unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Choosing a Display Description of displaysHeading display Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps Alarm Setup Alarm menuDgps alarm options Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Disable SV Disable satelliteOutput Data Data OUT1 menu, sentences Baud rate optionsHeading talker options Tx interval optionsIEC, Nmea version options Log pulse Log pulse optionsGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode WAAS/DGPS Setup Position fix mode optionsWAAS/DGPS menu Waas Search optionsAUTO/MANUAL options Provider GEO Satellite LongitudeGEO satellite and coverage area Operation HDG Backup options Others MenuOthers menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceSymptom Cause Remedy TroubleshootingTroubleshooting Diagnostics Diagnostic test1Test menu options Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoPrompt for exchanging battery Prompt for turning off the powerReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Data ERRAP-1 AppendixMenu Tree AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page