Furuno SC-50 manual System Configuration, System configuration

Page 6

SYSTEM CONFIGURATION

The SC-50 consists of an antenna, a display unit and a processor unit. The tri-antenna system accommodates three antennas/receiver units and is available in a low-profile radome type or open type. The tri-antenna system helps reduce the influence of ship's motion (rolling).

Antenna Unit

SC-303

Analog pitch

 

Analog roll

Processor Unit

SC-501

 

Log/Heading alarm

 

(Contact)

 

Antenna Unit

SC-603Display Unit

SC-502

OR

3

6 ports for Heading or Navigation Data (5 AD-10/IEC 61162 ports, 1 AD-10 port)

: Option

External heading data

External DPGS

 

Beacon Receiver

12-24 VDC

Category of Units

Processor Unit: Protected from weather

Display Unit: Protected from weather

Antenna Unit: Exposed to weather

System configuration

v

Image 6
Contents Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures ForewordWord to the Owner of the SC-50 System Configuration System configurationOptional equipment Equipment ListStandard supply Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Installation Mounting ConsiderationsAntenna unit Mast diameter Separation distance minimum Horizontal separation between antenna and mastsAntenna and field of view Example of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaAntenna unit SC-303 Coating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitMounting How to orient the antenna elementsAntenna unit SC-603 Antenna unit SC-603Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the antenna unit Fastening the antenna cable Antenna elementInstalling the Processor Unit Deck, bulkhead mountProcessor unit orientation, deck mounting Installation on the underside of a desk Installation of processor unit on the underside of a deskFlush mount Installing the Display UnitDesktop, overhead mounting Flush mount FFlush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring General wiring diagramProcessor unit, rear view How to install the optional antenna cable set Sectional view of coaxial cable 3D2VHow to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuHeading setup menu Choosing heading sourceSatellite tracking status display General wiring Connection of External EquipmentProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabricationOperation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run display Set and drift display, speed and distance run displayDgps alarm options Dgps Alarm SetupAlarm menu Buzzer optionsConfirming Satellite Status Satellite status displayGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Data OUT1 menu, sentences Baud rate optionsTx interval options IEC, Nmea version optionsHeading talker options Log pulse Log pulse optionsSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode WAAS/DGPS menu WAAS/DGPS SetupPosition fix mode options Waas Search optionsProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation Others menu HDG Backup optionsOthers Menu HDG Restoration optionsTrip Menu Trip menuResetting Distance Run Reset Distance promptThis page intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceTroubleshooting TroubleshootingSymptom Cause Remedy Test menu options DiagnosticsDiagnostic test1 Test start promptDiagnostic test sequence Push KEYDiagnostic test2 TEST2 displayDiagnostic test3 Alarm optionsProgram version no. display Program NumberClearing Data Prompts for erasure of dataPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Prompt for turning off the powerError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Data ERRAppendix Menu TreeAP-1 AP-2 Specifications SC-50Furuno Index IN-1Packing List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page