Furuno SC-50 manual Furuno

Page 67

FURUNO

SC-50

4POWER SUPPLY

12-24 VDC: 1.2-0.5 A

5ENVIRONMENTAL CONDITIONS AND EMC

5.1Ambient Temperature

	Display/Processor Unit	-15°C to +55°C, Designed for protected area
	Antenna Unit	-25°C to +70°C, Designed for exposed area
5.2	Damp Heat	93% ±3% at 40°C
5.3	Waterproofing
	Antenna Unit	IPX6
	Display Unit	IPX5
	Processor Unit	IPX0
5.4	Vibration	IEC 60945
5.5	EMC	IEC 60945
6	COATING COLOR
6.1	Display/Processor Unit	Panel: N3.0 Newtone No.5 (dark gray)
		Cover: 2.5GY5/1.5 (light gray)
6.2	Antenna Unit	N9.5 (white)

SP - 2

Image 67

Contents Satellite Compass Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingForeword FeaturesWord to the Owner of the SC-50 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListStandard supply Optional equipmentPrinciple of Operation This page intentionally left blank Mounting Considerations InstallationAntenna unit Horizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Display unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsAntenna unit SC-303 Cable from antenna No. marked on cable Waterproofing the antenna connectorHow to fasten the antenna cable Coating bolt, nut and washers with silicone sealantAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsAntenna unit SC-603 MountingFixing antenna unit to pedestal Orienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableDeck, bulkhead mount Installing the Processor UnitProcessor unit orientation, deck mounting Installation of processor unit on the underside of a desk Installation on the underside of a deskFlush mount F Installing the Display UnitDesktop, overhead mounting Flush mountFlush mount S kit Type OP20-17, Code No Flush mount SFlush mount S General wiring diagram WiringProcessor unit, rear view Sectional view of coaxial cable 3D2V How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBMain menu Initial SettingsInstallation setup menu Confirming satellite status choosing mounting methodChoosing heading source Heading setup menuSatellite tracking status display Connection of External Equipment General wiringProcessor unit, cover opened Cable Sectional view, fabrication Fabrication of cablesControls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Nav data display Choosing a DisplayDescription of displays Heading displayCompass display Steering displayROT Rate-of-Turn display Set and drift display, speed and distance run display Set and Drift display, Distance Run displayBuzzer options Dgps Alarm SetupAlarm menu Dgps alarm optionsSatellite status display Confirming Satellite StatusDisplaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Baud rate options Data OUT1 menu, sentencesIEC, Nmea version options Tx interval optionsHeading talker options Log pulse options Log pulseSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode Waas Search options WAAS/DGPS SetupPosition fix mode options WAAS/DGPS menuGEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation HDG Restoration options HDG Backup optionsOthers Menu Others menuTrip menu Trip MenuReset Distance prompt Resetting Distance RunThis page intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingTroubleshooting TroubleshootingSymptom Cause Remedy Test start prompt DiagnosticsDiagnostic test1 Test menu optionsPush KEY Diagnostic test sequenceTEST2 display Diagnostic test2Alarm options Diagnostic test3Prompts for erasure of data Program NumberClearing Data Program version no. displayPrompt for turning off the power Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryMessage display Replacement of FuseError Messages Error Message Meaning RemedyData ERR Error messages con’t from previousMenu Tree AppendixAP-1 AP-2 SC-50 SpecificationsFuruno IN-1 IndexＰａｃｋｉｎｇＬｉｓｔ SC-501-J/E SC-303 工事材料表 Installation Materials ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page