Furuno SC-50 manual Turning the Power On/Off, Panel Illumination, Display Contrast, Processor unit

Page 33

3. OPERATION

3.2Turning the Power On/Off

Use the power switch on the processor unit to turn the power to the display unit on and off.

POWER

Switch

Processor unit

The display starts up with the last-used display.

Note 1: Turn on external equipment AFTER the SC-50 is showing reliable heading data, to prevent heading output error.

Note 2: The display flashes when backup heading data is being used.

3.3Panel Illumination, Display Contrast

1. Press the [DIM] key.

DIMMER (1-8)

4

CONTRAST (0-63)

45

EXIT: [ENT]

Dialog box for adjustment of panel illumination, display contrast

2.Press ▲ or ▼ to adjust panel illumination.

3.Press or to adjust display contrast.

4.Press the [ENT] key.

3-2

Image 33
Contents Satellite Compass Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingFeatures ForewordWord to the Owner of the SC-50 System configuration System ConfigurationStandard supply Equipment ListOptional equipment Name Type Code No Qty RemarksPrinciple of Operation This page intentionally left blank Installation Mounting ConsiderationsAntenna unit Mast diameter Separation distance minimum Horizontal separation between antenna and mastsAntenna and field of view Display unit, processor unit Example of antenna installed below superstructuresInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaAntenna unit SC-303 How to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverAntenna unit SC-603 How to orient the antenna elementsMounting Antenna unit SC-603Fixing antenna unit to pedestal Orienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the antenna unit Antenna element Fastening the antenna cableInstalling the Processor Unit Deck, bulkhead mountProcessor unit orientation, deck mounting Installation of processor unit on the underside of a desk Installation on the underside of a deskDesktop, overhead mounting Installing the Display UnitFlush mount Flush mount FFlush mount S Flush mount S kit Type OP20-17, Code NoFlush mount S Wiring General wiring diagramProcessor unit, rear view Sectional view of coaxial cable 3D2V How to install the optional antenna cable setHow to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuHeading setup menu Choosing heading sourceSatellite tracking status display General wiring Connection of External EquipmentProcessor unit, cover opened Cable Sectional view, fabrication Fabrication of cablesOperation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Description of displays Choosing a DisplayHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and drift display, speed and distance run display Set and Drift display, Distance Run displayAlarm menu Dgps Alarm SetupDgps alarm options Buzzer optionsSatellite status display Confirming Satellite StatusGPS Setup Displaying the GPS setup menuGPS Setup menu description Disable SV Disable satellite Output DataHeading Baud rate options Data OUT1 menu, sentencesTx interval options IEC, Nmea version optionsHeading talker options Log pulse options Log pulseSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode Position fix mode options WAAS/DGPS SetupWAAS/DGPS menu Waas Search optionsProvider GEO Satellite Longitude GEO satellite and coverage areaAUTO/MANUAL options Operation Others Menu HDG Backup optionsOthers menu HDG Restoration optionsTrip menu Trip MenuReset Distance prompt Resetting Distance RunThis page intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingTroubleshooting TroubleshootingSymptom Cause Remedy Diagnostic test1 DiagnosticsTest menu options Test start promptPush KEY Diagnostic test sequenceTEST2 display Diagnostic test2Alarm options Diagnostic test3Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryPrompt for exchanging battery Prompt for turning off the powerError Messages Replacement of FuseError Message Meaning Remedy Message displayData ERR Error messages con’t from previousAppendix Menu TreeAP-1 AP-2 SC-50 SpecificationsFuruno IN-1 IndexPacking List SC-501-J/E SC-303 工事材料表 Installation Materials フラッシュマウントキット 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page