Schneider Electric PAS4S manual Shipping, storage, disposal, Lubricating the linear guide

Page 85

PAS4•S	8 Service, maintenance and disposal

Procedure

Lubricating the linear guide

Inject the correct type and volume of grease into the two outer grease nipples at one side of the carriage.

Lubricating the drive element

Inject the correct type and volume of grease into the center grease nipple at one side of the carriage.

8.3Shipping, storage, disposal

Note the ambient conditions on page 23.

Shipping The product must be protected against shocks during transportation. If possible, use the original packaging for shipping.

Storage The product may only be stored in spaces where the specified permis- sible ambient conditions for room temperature and humidity are met. Protect the product from dust and dirt.

Disposal The product consists of various materials that can be recycled and must be disposed of separately. Dispose of the product in accordance with lo- cal regulations.

MNA1MLSDM00EN, V2.01, 07.2009

Portal axes with ball screw drive

85

Image 85

Contents PAS4S Important information Table of contents Commissioning PAS4 S PAS4S Writing conventions and symbols PAS4S Features of the linear guide Features and options of the linear axisIntroduction Overview of product propertiesMotor mounting straight Motor mountingProduct overview ball screw axis Product overviewPAS Type code1200 100 Distance between carriages 1200 100 Motor / gearbox interface Axis drive interface Documentation and literature references MANUFACTURER’S Declaration Manufacturers DeclarationPAS4S Qualification of personnel Before you begin safety informationIntended use Great Mass or Falling Parts Basic informationLoss of Control Standards and terminology PAS4S Installation altitude Technical DataAmbient conditions PAS42SB PAS42PAS42AB 7800 7700 14900 Service life reference magnitudeCharacteristic curves PAS42SB LP mm Dimensional drawing PAS42SB Dimensional drawings PAS42SBCarriage type Type PAS43SB PAS43PAS43AB 13000 8600 17000 Service life reference magnitudeCharacteristic curves PAS43SB Nkrit rpm 3500 3000 2500 2000 1500 1000 4000 Dimensional drawing PAS43SB Dimensional drawings PAS43SBPAS4 S PAS44SB PAS44PAS44AB 22600 15000 18500 Service life reference magnitudeCharacteristic curves PAS44SB 500 1000 1500 2000 2500 3000 3500 Dimensional drawings PAS44SB Dimensional drawings PAS44SBPAS4 S Positioning accuracy and repeatability Service lifeMotor Stroke reservePAS42 PAS43 PAS44 PAS4S Motor Without Braking Effect InstallationHOT Surfaces Preparing installation Standard tightening torques Mechanical installationMounting the linear axis Mounting the contact plate ProcedureMounting the sensors Mounting the motor or the gearbox Motor mounting only Gearbox mounting only Mounting the payload Checking installation Electrical installationConnecting the sensors Motor connectionPAS4S Unexpected Movement CommissioningCommissioning procedure Troubleshooting Diagnostics and troubleshootingBall screw drive InspectionBall screw bearing Linear guideReplacing a sensor Replacing partsDismounting, gearbox only Prerequisites Dismounting, motor onlyMounting Replacing the elastomer couplingSharp Edges Replacing the cover strip and the strip deflectionPAS41 PAS42 PAS43 PAS44 Clamping plate PAS4S PAS4 S PAS4S Dimensional drawings Accessories and spare partsClamping claws Order dataLocating dowels Slot nutsSlot covers Sensors and additional parts Technical dataSensors Sensor holder Sensor extension cableContact plate Elastomer spiders Coupling assembliesSPM3MFR14A034 SPM3MFR20A120Clamping hubs 57.5 Cover strips Grease gunsCover strip clamp Strip deflectionMagnetic strips SPM3MAC2B042 Rubber bufferSPM3MAC3B043 SPM3MAC4B044PAS4S Service address Service, maintenance and disposalElectric Shock Cleaning MaintenanceDamage DUE to Wrong Lubricant LubricationLubricating the linear guide and the drive elements Lubricating the linear guide Shipping, storage, disposalPAS4S Terms and Abbreviations GlossaryPAS4S Index PAS4S PAS4S10 Index PAS4S