Invacare 96-100 Procedure Front Riggings, Installing Footrests Figure, Adjusting Footrest Height

Page 16

PROCEDURE 1

FRONT RIGGINGS

F

R O N T

R

I

G G I N G S

This Procedure includes the following:

Installing Footrests

Adjusting Footrest Height

Installing 3-inch Extension

Installing Elevating Legrests

Raising/Lowering Elevating Legrests and/or Adjusting Calfpads

Installing/Adjusting Adjustable Angle Flip-up Footplates

Replacing Sector Block

Optional Footrest Accessories

WARNING

After adjustments, and before use, make sure all attaching hardware is securely tightened.

INSTALLING FOOTRESTS (FIGURE 1)

1.Turn the footrest to the side (open footplate is perpendicular to wheelchair).

2.Insert mounting pin into mounting tube.

3.Push the footrest towards the inside of the wheelchair until it locks into place.

NOTE: The footplate will be on the inside of the wheelchair when locked in place.

4.Repeat this procedure for the opposite footrest.

5.To release the footrest, push the footrest release lever inward, rotate footrest outward.

Mounting Pin

Footrest

Release

Lever

Footrest

Mounting

Tube

Footplate

NOTE: All swingaway style footrests are installed the same way. Only one (1) style of footrest is shown for clarity.

FIGURE 1 - INSTALLING FOOTRESTS

ADJUSTING FOOTREST HEIGHT

NOTE: Release the footrest locking mechanism and lift the mounting pin out of the mounting tube. Lay the assembly on a flat surface to simplify procedure.

Pivot Slide Tube Height Adjustment (FIGURE 2)

1.Remove any accessories that are attached to the footrests.

2.Remove the hex screw and coved washer and posi- tion the footrest assembly to the desired height.

3.Lineup the mounting hole in the footrest support, reinsert the hex screw and coved washer and se- curely tighten.

4.Repeat STEPS 1-3for the other footrest.

5.Reinstall any accessories that are attached to the footrest.

Hex Screw

Coved Washer

Footrest

FIGURE 2 - PIVOT SLIDE TUBE HEIGHT

ADJUSTMENT

Footplate Height Adjustment (70o MFX and 90o Footrests Only) (FIGURE 3)

1.Remove any accessories that are attached to the footrests.

2.Remove the socket bolt, coved washer and locknut that secure the footplate to the footrest support.

3.Reposition the footplate to the desire height.

WARNING

DO NOT overtighten. Footrest must be able to rotate upward from the horizontal to vertical position.

4.Reinstall the socket bolt through the mounting holes of the footplate and footrest support.

5.Secure the footplate to the footrest support with the coved washer and locknut.

 

Footrest Support

 

Height Adjustment

Locknut

Holes

 

 

Socket Bolt

 

Footplate

FIGURE 3 - FOOTPLATE HEIGHT ADJUSTMENT

(70O MFX AND 90O FOOTRESTS ONLY)

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsPercentage of Weight Distribution Unoccupied OccupiedNON-RECLINERS ReclinersFolding and Unfolding Wheelchair SAFETY/HANDLING Functional Reach from a WheelchairBending Forward Recliners only Sling Seat Model Wheelchairs Unfolding FoldingSling Seat Model Wheelchairs Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsPackaging HandlingC K a G I N G N D L I N GSafety Inspection Checklist Safety Inspection Check ListMaintenance TroubleshootingI N T E N a N C E Procedure Front Riggings Installing Footrests FigureAdjusting Footrest Height Pivot Slide Tube Height Adjustment FigureInstalling 3-INCH Extension Figure Installing Elevating Legrests FigureProcedure Raising/Lowering Elevating LegrestsAdjusting Calfpads INSTALLING/ADJUSTING Adjustable Angle FLIP-UP FootplatesInstalling Adjustable Angle Flip-up Footplates Figure Adjustable Angle Flip-up Footplate Depth Adjustment FigureOptional Footrest Accessories Replacing Sector Block FigureFLIP-UP Footplates Figure Aluminum or Composite Footplates FigureInstalling Procedure ArmsM S Adjusting the T Arms RemovingHeight Figure Width FigureArm Sockets Figure Reposition the arm tube on the T arm postArm Hex Screws Washers Arms Procedure Replacing the Locking Lever T Arms FigureTop Middle Bottom Side Arm Guard Socket Screws Bottom ClampInstalling/Height Adjustment Figure Using FigureCorresponding Arm Adjustment to Back Angle Figures 10 Adjustment ReplacementAngled Portion Cantilever Arm Locking Mechanism Actuator Apply LoctiteInstalling Fabric Clothing Guards Figure Adjusting Conventional Arm HeightInstalling Rigid Side Guards Figure Removing Conventional ArmsRear Arm Sockets Figure Replacing Armrest Pads FigureFront Arm Sockets Figure Procedure Back Installing Adjustable Back Upholstery FigureC K Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsBack Upholstery Cover WHY USE Adjustable Back Upholstery a Clinical DiscussionBack upholstery cover is designed for three 3 reasons Adjusting the Back Height Adjustable Height Backs FigureRecliner Back Upholstery Figure Recliner Headrest Upholstery FigureSlowly remove the two 2 backs canes from the wheelchair Fixed Height Backs FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Changing the Back Angle Repositioning the Back Changing Seat DepthBack Plate Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureRecliner Brackets Installing and Removing a Seating SystemReplacing Folding Push Handle Recliners only Figure A T SeatCHANGING/REPOSITIONING Seat Rails Figure Replacing Seat Upholstery FigureProcedure Seat Repositioning the Crossbraces FigureChanging Seat Width Standard Folding Frames FigureFor installation of new Pivot LinkCrossbraces Folding Frames Without Seat Rails FigureRigid Frames Figure Hex Bolt Seat Width HolesCrossmembers Wheelchair Frame Washer Hex Screws Casters S T E R SReplacing Front Fork Figure REPLACING/REPAIRING Front Caster TIRE/TUBE CastersInline Caster Headtubes Figure Offset Caster Headtubes FigureCaster Headtube Mounting Adjustments Figure Height AdjustmentRepositioning the Caster Headtubes Inline Caster Headtube Hardware OffsetDust Release Detent Pin Installing QUICK-RELEASE Casters FigureCover Headtube Locknut Cap Spacer Fork Stem Hex Screw REMOVING/INSTALLING Rear Wheels Figure Adjusting the QUICK-RELEASE Axle FigureA R Rear WheelsInstalling the QUAD-RELEASE Axle Figure Adjusting the QUAD-RELEASE Handle FigureJusting the QUAD-RELEASE Handle And/or OutHandrim Replacement Figure Removing the Play From the Rear WheelsSpoke Rear Wheels Phillips Bolt HandrimInstalling Projection Handrims Composite Rear Wheels FigureComposite Rim Locknut Spoke Rear Wheels FigureREPAIRING/REPLACING Rear Wheel TIRE/ Tube Adjusting the Wheelbase Length FigureJam Nuts Shortening ForwardAdjusting the Wheelbase Width Figure Adjusting Rear Wheel Height FigureAxle Mounting PlateAdjusting the Wheel Locks Figure Wheel Lock Extension Handle Installation FigureE E L K S E R S Wheel LOCKS/ANTI-TIPPERSProcedure Wheel LOCKS/ANTI-TIPPERS INSTALLING/ADJUSTING the ANTI-TIPPERSAdjusting the Anti-Tippers Figure Installing the Anti-Tippers FigureREPLACEMENT/ADJUSTMENT ReclinerRecliner Operation Figures 1 Folding/Unfolding the WheelchairInstalling New Recliner Cables Actuator Housing Cable Locking NutRecliner Trigger Release LeverReplacing the GAS Cylinders Figure Must Look TOO LOWLike this Steps 1, 5Adjusting the GAS Cylinders Figure Trigger Release Lever Cable Locking Nut AdjustingSqueeze the handles to extend the new gas cylinders Detail B Must Look TOO LOWSEAT-TO-FLOOR SEAT-TO-FLOOR Height DeterminationMinus EqualsChanging SEAT-TO-FLOOR Height Procedure SEAT-TO-FLOORStandard MULTI-POSITION Axle Plate A T Lower Inline Caster Headtube Front SEAT-TO-FLOOR HeightsFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights A T P T H Seat Depth Determination FigureChanging Seat Depth Seat DepthSeat Depth Checklist Seat DepthA T P T LeftRight Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents