Invacare 1061057, 96-100 manual Replacing Sector Block Figure, Optional Footrest Accessories

Page 19

FRONT RIGGINGS

PROCEDURE 1

REPLACING SECTOR BLOCK (FIGURE 10)

1.Remove the hex screw and washer that secure the existing sector block to the wheelchair frame.

2.Position the new sector block on the wheelchair frame. Make sure the locking pin is facing UP.

3.Secure the new sector block to the wheelchair frame with the existing hex screw and washer.

 

Hex Screw

Wheelchair

Washer

Frame

 

Sector Block

Locking Pin

FIGURE 10 - REPLACING SECTOR BLOCK

OPTIONAL FOOTREST ACCESSORIES

Impact Guards/Calf Strap/H-Calf Strap (FIGURE 11)

NOTE: Impact Guards are Standard Equipment on Model ST Footrests. No assembly is required.

1.Remove impact guard/calf strap from packaged con- tainer.

2.Secure the impact guards to the footrest frame.

3.Secure the calf strap around the footrest frame (with the impact guards attached).

Impact Guard

H-Calf Strap

3.Remove the phillips bolt and locknut that secure the heel loop to the footplate.

4.Slide heel loop over the pivot tube.

5.Replace heel loop.

6.Reverse STEPS 1-5to install the new heel loop.

NOTE: When securing the heel loop to the footrest assembly, tighten the phillips bolt and locknut until the spacer is secure.

Footrest

Hex Screw/Support

Coved Washer

Heel Loop

Phillips Bolt

Pivot Tube

Spacer

Footplate

Locknut

FIGURE 12 - REPLACING HEEL LOOPS - ALUMINUM OR COMPOSITE FOOTPLATES

FLIP-UP FOOTPLATES (FIGURE 13).

1.Remove the four (4) phillips screws and washers that secure the heel loop to the footplate.

2.Remove the existing heel loop from the footplate.

3.Position the new heel loop UNDER the footplate.

NOTE: If the heel loop is equipped with an ankle strap, position the heel loop on TOP of the footplate.

4.Line up mounting holes in footplate and heel loop.

5.Secure the new heel loop to the footplate with the four (4) existing phillips screws and washers.

Footplate

Heel Loop

F

R O N T

R

I

G G I N G S

Calf Strap

FIGURE 11 - IMPACT GUARDS/CALF STRAP/

H-CALF STRAP

Replacing Heel Loops

ALUMINUM OR COMPOSITE FOOTPLATES (FIGURE 12).

1.Remove the hex screw and coved washer that se- cure the pivot tube and footplate to footrest support.

2.Remove the pivot tube and footplate from the foot- rest support.

Phillips Screws

Washers

Phillips Screws

Washers

Heel Loop with

Ankle Strap

Footplate

FIGURE 13 - REPLACING HEEL LOOPS -

FLIP-UP FOOTPLATES

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysRecliners Percentage of Weight DistributionUnoccupied Occupied NON-RECLINERSFolding and Unfolding Wheelchair SAFETY/HANDLING Functional Reach from a WheelchairBending Forward Solid Seat Model Wheelchairs Recliners onlySling Seat Model Wheelchairs Unfolding Folding Sling Seat Model Wheelchairs FoldingFeatures FeaturesA T U R E S Specifications SpecificationsN D L I N G PackagingHandling C K a G I N GSafety Inspection Check List Safety Inspection ChecklistMaintenance TroubleshootingI N T E N a N C E Pivot Slide Tube Height Adjustment Figure Procedure Front RiggingsInstalling Footrests Figure Adjusting Footrest HeightRaising/Lowering Elevating Legrests Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure ProcedureAdjustable Angle Flip-up Footplate Depth Adjustment Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Installing Adjustable Angle Flip-up Footplates FigureAluminum or Composite Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure FLIP-UP Footplates FigureInstalling Procedure ArmsM S Width Figure Adjusting the T ArmsRemoving Height FigureArm Sockets Figure Reposition the arm tube on the T arm postArm Hex Screws Washers Socket Screws Bottom Clamp Arms ProcedureReplacing the Locking Lever T Arms Figure Top Middle Bottom Side Arm GuardInstalling/Height Adjustment Figure Using FigureCorresponding Arm Adjustment to Back Angle Figures 10 Locking Mechanism Actuator Apply Loctite AdjustmentReplacement Angled Portion Cantilever ArmRemoving Conventional Arms Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Installing Rigid Side Guards FigureRear Arm Sockets Figure Replacing Armrest Pads FigureFront Arm Sockets Figure Replacing Back Upholstery Procedure BackInstalling Adjustable Back Upholstery Figure C KAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureBack Upholstery Cover WHY USE Adjustable Back Upholstery a Clinical DiscussionBack upholstery cover is designed for three 3 reasons Recliner Headrest Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Back Upholstery FigureSlowly remove the two 2 backs canes from the wheelchair Fixed Height Backs FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Non-Recliners Figure Changing the Back AngleRepositioning the Back Changing Seat Depth Back PlateRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherRecliner Brackets Installing and Removing a Seating SystemReplacing Folding Push Handle Recliners only Figure Replacing Seat Upholstery Figure A TSeat CHANGING/REPOSITIONING Seat Rails FigureStandard Folding Frames Figure Procedure SeatRepositioning the Crossbraces Figure Changing Seat WidthFolding Frames Without Seat Rails Figure For installation of newPivot Link CrossbracesRigid Frames Figure Hex Bolt Seat Width HolesCrossmembers Wheelchair Frame Washer Hex Screws Casters S T E R SReplacing Front Fork Figure Offset Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Inline Caster Headtubes FigureInline Caster Headtube Hardware Offset Caster Headtube Mounting Adjustments FigureHeight Adjustment Repositioning the Caster HeadtubesDust Release Detent Pin Installing QUICK-RELEASE Casters FigureCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Rear Wheels REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure A RAnd/or Out Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure Justing the QUAD-RELEASE HandlePhillips Bolt Handrim Handrim Replacement FigureRemoving the Play From the Rear Wheels Spoke Rear WheelsSpoke Rear Wheels Figure Installing Projection HandrimsComposite Rear Wheels Figure Composite Rim LocknutShortening Forward REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Jam NutsMounting Plate Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure AxleWheel LOCKS/ANTI-TIPPERS Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure E E L K S E R SInstalling the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Adjusting the Anti-Tippers FigureFolding/Unfolding the Wheelchair REPLACEMENT/ADJUSTMENTRecliner Recliner Operation Figures 1Trigger Release Lever Installing New Recliner CablesActuator Housing Cable Locking Nut ReclinerSteps 1, 5 Replacing the GAS Cylinders FigureMust Look TOO LOW Like thisDetail B Must Look TOO LOW Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Squeeze the handles to extend the new gas cylindersEquals SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination MinusChanging SEAT-TO-FLOOR Height Procedure SEAT-TO-FLOORStandard MULTI-POSITION Axle Plate A T Lower Inline Caster Headtube Front SEAT-TO-FLOOR HeightsFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth A T P T HSeat Depth Determination Figure Changing Seat DepthSeat Depth Seat Depth ChecklistRear Mounting Hole A T P TLeft RightApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents