Invacare 96-100, 1061057 manual Trigger Release Lever, Removing Existing Recliner Cables

Page 54

PROCEDURE 8

RECLINER

R E C L I N E R

6.SLOWLY, squeeze the handles of the recliner cable assemblies and allow the back to recline to the de- sired angle.

7.When the back reaches desired angle, slowly release the handles of the recliner cable assemblies.

8.To return the back to the full upright position, reverse the above steps keeping in mind proper body me- chanics.

Trigger

Release

Lever

FIGURE 2 - RECLINER OPERATION

ADJUSTING THE RECLINER CABLES

NOTE: Refer to ADJUSTING THE GAS CYLINDERS in this section of the manual.

REPLACING THE RECLINER CABLES (FIGURE 3)

NOTE: For ease of assembly, replace one (1) recliner cable at a time.

Removing Existing Recliner Cables

1.While holding the locknut in the trigger release lever, remove the phillips bolt that secures the handle to the back cane.

2.Remove the trigger release lever from the back cane.

3.Cut the tie wraps that secure the existing recliner cable to the back cane.

NOTE: Refer to DETAIL "A" for STEPS 4-7.

4.Loosen the cable locking nut that secures the existing recliner cable to the trigger release lever.

5.Unscrew the cable locking collar that secures the ex- isting recliner cable to the trigger release lever.

6.Remove the end of the existing recliner cable from the slot in the trigger release lever.

7.Unscrew the fitting end of the existing recliner cable from the trigger release lever.

8.Unscrew the cable locking nut that secures the exist- ing recliner cable to the actuator housing.

9.Remove the end of the existing recliner cable from the actuator.

10.Remove the existing recliner cable from the wheel- chair.

Installing New Recliner Cables

1.Screw the new recliner cable into the trigger release lever until the fitting end of the cable is flush with the inside of the handle. Refer to DETAIL "A".

2.Reinstall the locknut into the trigger release lever, if necessary.

NOTE: Refer to DETAIL "A" for STEPS 3-6.

3.Install the end of the new recliner cable into the slot in the trigger release lever.

4.Screw the cable locking collar onto the trigger release lever until the collar bottoms out on the trigger release lever.

 

DETAIL "A"

Trigger

 

Release

Recliner

Lever

Cable

Cable

Fitting End

Locking

Cable Locking Collar

Nut

 

Phillips

 

Bolt

 

Back Cane

Locknut

Tie

Wraps

 

Actuator

Housing

Cable

Locking

Nut

FIGURE 3 - REPLACING THE RECLINER CABLES

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsNON-RECLINERS Percentage of Weight DistributionUnoccupied Occupied ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Sling Seat Model Wheelchairs Folding Recliners onlySling Seat Model Wheelchairs Unfolding Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsC K a G I N G PackagingHandling N D L I N GSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceI N T E N a N C E Adjusting Footrest Height Procedure Front RiggingsInstalling Footrests Figure Pivot Slide Tube Height Adjustment FigureProcedure Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure Raising/Lowering Elevating LegrestsInstalling Adjustable Angle Flip-up Footplates Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjustable Angle Flip-up Footplate Depth Adjustment FigureFLIP-UP Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Height Figure Adjusting the T ArmsRemoving Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Top Middle Bottom Side Arm Guard Arms ProcedureReplacing the Locking Lever T Arms Figure Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Angled Portion Cantilever Arm AdjustmentReplacement Locking Mechanism Actuator Apply LoctiteInstalling Rigid Side Guards Figure Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure C K Procedure BackInstalling Adjustable Back Upholstery Figure Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Recliner Back Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Back Plate Changing the Back AngleRepositioning the Back Changing Seat Depth Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure CHANGING/REPOSITIONING Seat Rails Figure A TSeat Replacing Seat Upholstery FigureChanging Seat Width Procedure SeatRepositioning the Crossbraces Figure Standard Folding Frames FigureCrossbraces For installation of newPivot Link Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure Inline Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Offset Caster Headtubes FigureRepositioning the Caster Headtubes Caster Headtube Mounting Adjustments FigureHeight Adjustment Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw A R REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure Rear WheelsJusting the QUAD-RELEASE Handle Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure And/or OutSpoke Rear Wheels Handrim Replacement FigureRemoving the Play From the Rear Wheels Phillips Bolt HandrimComposite Rim Locknut Installing Projection HandrimsComposite Rear Wheels Figure Spoke Rear Wheels FigureJam Nuts REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Shortening ForwardAxle Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure Mounting PlateE E L K S E R S Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the Anti-Tippers FigureRecliner Operation Figures 1 REPLACEMENT/ADJUSTMENTRecliner Folding/Unfolding the WheelchairRecliner Installing New Recliner CablesActuator Housing Cable Locking Nut Trigger Release LeverLike this Replacing the GAS Cylinders FigureMust Look TOO LOW Steps 1, 5Squeeze the handles to extend the new gas cylinders Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Detail B Must Look TOO LOWMinus SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Changing Seat Depth A T P T HSeat Depth Determination Figure Seat DepthSeat Depth Checklist Seat DepthRight A T P TLeft Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents