Invacare 1061057, 96-100 manual Arms Procedure, Replacing the Locking Lever T Arms Figure

Page 23

ARMS

PROCEDURE 2

3. Move the bottom clamp to one (1) of three (3)

3. Remove the existing locking lever and spring from

mounting holes in the side guard.

the bottom bracket.

NOTE: The middle mounting hole is the stan- dard mounting position for rigid wheelchairs.

NOTE: The bottom mounting hole is the stan- dard mounting position for folding wheelchairs.

NOTE: The top mounting hole is an optional mounting position for folding or rigid wheelchairs.

4.Re-secure the side guard to the bottom clamp with the socket screw.

5.Install the "T" arm onto the wheelchair. Refer to INSTALLING/REMOVING THE "T" ARMS in this section of the manual.

Top

 

 

Middle

 

 

Bottom

Side

"T" Arm

 

Guard

 

 

 

 

Transfer

NOTE: Inspect the spring and replace if necessary.

4.Position the spring on the bottom bracket as shown in FIGURE 8.

5.Position the new locking lever onto the spring and the bottom bracket.

NOTE: Make sure the two (2) extended ends of the spring are inside the notch in the locking lever.

6.Line up the mounting holes in the new locking lever, spring and bottom bracket.

WARNING

DO NOT over tighten the locknut that secures the locking lever to the bottom bracket. Over tightening this locknut will prevent the locking lever from oper- ating properly, possibly causing injury.

7.Install the phillips bolt and tighten securely with the locknut.

8.Install the "T" arm onto the wheelchair. Refer to IN- STALLING/REMOVING THE "T" ARMS in this sec- tion of the manual.

A R M S

Assist

Socket

Screws

Bottom Clamp

FIGURE 7 - ADJUSTING THE TRANSFER

ASSISTS AND/OR SIDE GUARDS - "T" ARMS

REPLACING THE LOCKING LEVER - "T" ARMS (FIGURE 8)

Bottom

Bracket

Phillips Bolt

Extended Ends

Spring

Notch

Locknut

Locking

Lever

1.Remove the "T" arm from the wheelchair. Refer to INSTALLING/REMOVING THE "T" ARMS in this section of the manual.

2.Remove the phillips bolt and locknut that secure the existing locking lever to the bottom bracket.

CAUTION

The locking lever is spring loaded. Place your free hand over the locking lever to prevent the parts from springing off of the bottom bracket.

FIGURE 8 - REPLACING THE LOCKING LEVER

- "T" ARMS

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysRecliners Percentage of Weight DistributionUnoccupied Occupied NON-RECLINERSBending Forward SAFETY/HANDLING Functional Reach from a WheelchairFolding and Unfolding Wheelchair Solid Seat Model Wheelchairs Recliners onlySling Seat Model Wheelchairs Unfolding Folding Sling Seat Model Wheelchairs FoldingA T U R E S FeaturesFeatures Specifications SpecificationsN D L I N G PackagingHandling C K a G I N GSafety Inspection Check List Safety Inspection ChecklistI N T E N a N C E TroubleshootingMaintenance Pivot Slide Tube Height Adjustment Figure Procedure Front RiggingsInstalling Footrests Figure Adjusting Footrest HeightRaising/Lowering Elevating Legrests Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure ProcedureAdjustable Angle Flip-up Footplate Depth Adjustment Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Installing Adjustable Angle Flip-up Footplates FigureAluminum or Composite Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure FLIP-UP Footplates FigureM S Procedure ArmsInstalling Width Figure Adjusting the T ArmsRemoving Height FigureArm Hex Screws Washers Reposition the arm tube on the T arm postArm Sockets Figure Socket Screws Bottom Clamp Arms ProcedureReplacing the Locking Lever T Arms Figure Top Middle Bottom Side Arm GuardCorresponding Arm Adjustment to Back Angle Figures 10 Using FigureInstalling/Height Adjustment Figure Locking Mechanism Actuator Apply Loctite AdjustmentReplacement Angled Portion Cantilever ArmRemoving Conventional Arms Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Installing Rigid Side Guards FigureFront Arm Sockets Figure Replacing Armrest Pads FigureRear Arm Sockets Figure Replacing Back Upholstery Procedure BackInstalling Adjustable Back Upholstery Figure C KAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureBack upholstery cover is designed for three 3 reasons WHY USE Adjustable Back Upholstery a Clinical DiscussionBack Upholstery Cover Recliner Headrest Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Back Upholstery FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Fixed Height Backs FigureSlowly remove the two 2 backs canes from the wheelchair Replacing the Locking Mechanism in the Back Cane Figure Non-Recliners Figure Changing the Back AngleRepositioning the Back Changing Seat Depth Back PlateRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherReplacing Folding Push Handle Recliners only Figure Installing and Removing a Seating SystemRecliner Brackets Replacing Seat Upholstery Figure A TSeat CHANGING/REPOSITIONING Seat Rails FigureStandard Folding Frames Figure Procedure SeatRepositioning the Crossbraces Figure Changing Seat WidthFolding Frames Without Seat Rails Figure For installation of newPivot Link CrossbracesCrossmembers Wheelchair Frame Washer Hex Screws Hex Bolt Seat Width HolesRigid Frames Figure Replacing Front Fork Figure S T E R SCasters Offset Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Inline Caster Headtubes FigureInline Caster Headtube Hardware Offset Caster Headtube Mounting Adjustments FigureHeight Adjustment Repositioning the Caster HeadtubesCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Installing QUICK-RELEASE Casters FigureDust Release Detent Pin Rear Wheels REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure A RAnd/or Out Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure Justing the QUAD-RELEASE HandlePhillips Bolt Handrim Handrim Replacement FigureRemoving the Play From the Rear Wheels Spoke Rear WheelsSpoke Rear Wheels Figure Installing Projection HandrimsComposite Rear Wheels Figure Composite Rim LocknutShortening Forward REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Jam NutsMounting Plate Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure AxleWheel LOCKS/ANTI-TIPPERS Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure E E L K S E R SInstalling the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Adjusting the Anti-Tippers FigureFolding/Unfolding the Wheelchair REPLACEMENT/ADJUSTMENTRecliner Recliner Operation Figures 1Trigger Release Lever Installing New Recliner CablesActuator Housing Cable Locking Nut ReclinerSteps 1, 5 Replacing the GAS Cylinders FigureMust Look TOO LOW Like thisDetail B Must Look TOO LOW Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Squeeze the handles to extend the new gas cylindersEquals SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination MinusStandard MULTI-POSITION Axle Plate Procedure SEAT-TO-FLOORChanging SEAT-TO-FLOOR Height A T Frame Inline Caster Headtube Front SEAT-TO-FLOOR HeightsLower Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth A T P T HSeat Depth Determination Figure Changing Seat DepthSeat Depth Seat Depth ChecklistRear Mounting Hole A T P TLeft RightApproximate 2-inch gap A T P T Inch Right A T P T H Page R R a N T Y Limited WarrantyLimited Warranty One Invacare Way Technical Support
Top Page Image Contents