Invacare 96-100, 1061057 manual Installing Projection Handrims, Composite Rear Wheels Figure

Page 48

PROCEDURE 6

REAR WHEELS

R E A R

W

H

E

E

L

S

5.Reinstall rear wheel to the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual.

6.If the locking pins of the quick/quad-release axles are not protruding past the inside of the axle bush- ing or there is too much movement of the rear wheel assembly in a back and forth position, refer to ADJUSTING THE QUICK-RELEASE AXLE or ADJUSTING THE QUAD-RELEASE HANDLE in this section of the manual.

7.Repeat the procedure for the opposite rear wheel if necessary.

INSTALLING PROJECTION HANDRIMS

NOTE: The following procedures will work for any type of projection handrim.

Composite Rear Wheels (FIGURE 6)

1.Remove the rear wheel from the wheelchair.

2.Remove the existing handrim from the rear wheel. Refer to HANDRIM REPLACEMENT in this sec- tion of the manual.

3.Using the LONG screws, assemble the links to the projection handrim.

4.Position one (1) link with one (1) of the mounting holes in the rear wheel.

Composite Rim

Locknut

LONG

Screw

Link

SHORT Washer

Screw

Links at an approximate 45o

Angle in the same direction

Projection

Handrim

5.Install a SHORT screw through the link and the rear wheel and loosely tighten with washer and locknut.

6.Repeat STEPS 3 and 4 for one (1) link on the oppo- site side of the rear wheel.

NOTE: The links will attach to the rear wheel at an approximate 45o angle in the same direction.

7.Repeat STEPS 3 and 4 for the remaining links.

8.Securely tighten the washers and locknuts that se- cure the projection handrim to the rear wheel.

9.Reinstall the rear wheel onto the wheelchair.

10.If the locking pins of the quick/quad-release axles are not protruding past the inside of the axle bushing or there is too much movement of the rear wheel assembly in a back and forth position, refer to AD- JUSTING THE QUICK-RELEASE AXLE or AD- JUSTING THE QUAD-RELEASE HANDLE in this section of the manual.

11.Repeat the procedure for the opposite rear wheel.

Spoke Rear Wheels (FIGURE 7)

1. Remove the rear wheel from the wheelchair.

WARNING

Tire MUST be deflated before any disassembly pro- cedures are performed.

2.Remove all air from the bar by pressing down on the pin in the center of the valve stem.

3.While carefully holding the tire, bar and rim strip to one side, hold the phillips bolts and remove the lock- nuts that secure the handrim to the rear wheel.

4.Remove the existing handrim from the rear wheel.

5.Position the projection handrim mounting holes with the mounting holes in the rear wheel.

6.While carefully holding the tire, bar and rim strip to one side, hold the phillips bolts and securely tighten the locknuts that secure the handrim to the rear wheel.

Phillips

Bolts

Handrim

Locknut

FIGURE 6 - INSTALLING PROJECTION

FIGURE 7 - INSTALLING PROJECTION

HANDRIMS - COMPOSITE REAR WHEELS

HANDRIMS - SPOKE REAR WHEELS

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsPercentage of Weight Distribution Unoccupied OccupiedNON-RECLINERS ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Recliners only Sling Seat Model Wheelchairs Unfolding FoldingSling Seat Model Wheelchairs Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsPackaging HandlingC K a G I N G N D L I N GSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceI N T E N a N C E Procedure Front Riggings Installing Footrests FigureAdjusting Footrest Height Pivot Slide Tube Height Adjustment FigureInstalling 3-INCH Extension Figure Installing Elevating Legrests FigureProcedure Raising/Lowering Elevating LegrestsAdjusting Calfpads INSTALLING/ADJUSTING Adjustable Angle FLIP-UP FootplatesInstalling Adjustable Angle Flip-up Footplates Figure Adjustable Angle Flip-up Footplate Depth Adjustment FigureOptional Footrest Accessories Replacing Sector Block FigureFLIP-UP Footplates Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Adjusting the T Arms RemovingHeight Figure Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Arms Procedure Replacing the Locking Lever T Arms FigureTop Middle Bottom Side Arm Guard Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Adjustment ReplacementAngled Portion Cantilever Arm Locking Mechanism Actuator Apply LoctiteInstalling Fabric Clothing Guards Figure Adjusting Conventional Arm HeightInstalling Rigid Side Guards Figure Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure Procedure Back Installing Adjustable Back Upholstery FigureC K Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Adjusting the Back Height Adjustable Height Backs FigureRecliner Back Upholstery Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Changing the Back Angle Repositioning the Back Changing Seat DepthBack Plate Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure A T SeatCHANGING/REPOSITIONING Seat Rails Figure Replacing Seat Upholstery FigureProcedure Seat Repositioning the Crossbraces FigureChanging Seat Width Standard Folding Frames FigureFor installation of new Pivot LinkCrossbraces Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure REPLACING/REPAIRING Front Caster TIRE/TUBE CastersInline Caster Headtubes Figure Offset Caster Headtubes FigureCaster Headtube Mounting Adjustments Figure Height AdjustmentRepositioning the Caster Headtubes Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw REMOVING/INSTALLING Rear Wheels Figure Adjusting the QUICK-RELEASE Axle FigureA R Rear WheelsInstalling the QUAD-RELEASE Axle Figure Adjusting the QUAD-RELEASE Handle FigureJusting the QUAD-RELEASE Handle And/or OutHandrim Replacement Figure Removing the Play From the Rear WheelsSpoke Rear Wheels Phillips Bolt HandrimInstalling Projection Handrims Composite Rear Wheels FigureComposite Rim Locknut Spoke Rear Wheels FigureREPAIRING/REPLACING Rear Wheel TIRE/ Tube Adjusting the Wheelbase Length FigureJam Nuts Shortening ForwardAdjusting the Wheelbase Width Figure Adjusting Rear Wheel Height FigureAxle Mounting PlateAdjusting the Wheel Locks Figure Wheel Lock Extension Handle Installation FigureE E L K S E R S Wheel LOCKS/ANTI-TIPPERSProcedure Wheel LOCKS/ANTI-TIPPERS INSTALLING/ADJUSTING the ANTI-TIPPERSAdjusting the Anti-Tippers Figure Installing the Anti-Tippers FigureREPLACEMENT/ADJUSTMENT ReclinerRecliner Operation Figures 1 Folding/Unfolding the WheelchairInstalling New Recliner Cables Actuator Housing Cable Locking NutRecliner Trigger Release LeverReplacing the GAS Cylinders Figure Must Look TOO LOWLike this Steps 1, 5Adjusting the GAS Cylinders Figure Trigger Release Lever Cable Locking Nut AdjustingSqueeze the handles to extend the new gas cylinders Detail B Must Look TOO LOWSEAT-TO-FLOOR SEAT-TO-FLOOR Height DeterminationMinus EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights A T P T H Seat Depth Determination FigureChanging Seat Depth Seat DepthSeat Depth Checklist Seat DepthA T P T LeftRight Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents