Invacare 1061057, 96-100 Installing 3-INCH Extension Figure, Installing Elevating Legrests Figure

Page 17

FRONT RIGGINGS

PROCEDURE 1

INSTALLING 3-INCH EXTENSION (FIGURE 4)

NOTE: Make sure to note position of hardware before disassembly of the footrest.

NOTE: If using ANY type of extension with the ADJUSTABLE ANGLE FOOTPLATE, refer to

INSTALLING/ADJUSTING ADJUSTABLE ANGLE FLIP-UP FOOTPLATES in this section of the manual.

1.Remove any accessories that are attached to the footrests.

2.Remove the socket bolt, coved washer and lock- nut that secure the footplate to the footrest sup- port.

3.Insert the 3-inch extension into the footrest sup- port and align the mounting holes.

4.Secure the 3-inch extension to the footrest sup- port with new hex bolt, washer and locknut.

5.Position the footplate at the desired height.

WARNING

DO NOT overtighten. Footrest must be able to rotate upward from the horizontal to vertical po- sition.

6.Reinstall the socket bolt through the mounting holes of the footplate and footrest support.

7.Secure the footplate to the footrest support with the coved washer and locknut.

LocknutWasher

Footrest

Hex Bolt

Support

 

3-inch

Socket Bolt,

Coved Washer

Extension

and Locknut

 

FIGURE 4 - INSTALLING 3-INCH EXTENSION

INSTALLING ELEVATING LEGRESTS (FIGURE 5)

1.Insert the pivot tube into the legrest support and secure it with the bolt and nut.

2.Place legrest on the outside of the wheelchair and insert the mounting pin into the mounting tube.

3.Rotate legrest toward the inside of the wheelchair until it locks in place.

NOTE: The footplate will be on the inside of the wheelchair when locked in place.

4.Repeat STEPS 1-3for the opposite legrest.

5.After seated in wheelchair, adjust footrest to cor- rect height by loosening nut and sliding the pivot tube up or down until desired height is obtained.

6.To release the legrest, push the legrest release handle toward the inside of the wheelchair and swing the legrest to the outside of the wheelchair.

Mounting

Mounting Pin

Tube

 

Legrest

Release

Handle

Legrest

Support

Bolt and Nut

Pivot Tube

 

Footplate

FIGURE 5 - INSTALLING ELEVATING LEGRESTS

RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6)

Raising/Lowering Elevating Legrests

1.Perform one (1) of the following:

RAISING - Pull back on the release lever un- til the leg is at the desired height.

LOWERING - Support leg with one (1) hand and push release lever downward with other hand.

Release Lever

Calfpad Rotated For

 

Height Adjustment

Calfpad

FIGURE 6 - RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS

F

R O N T

R

I

G G I N G S

17

Image 17
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysUnoccupied Occupied Percentage of Weight DistributionNON-RECLINERS ReclinersBending Forward SAFETY/HANDLING Functional Reach from a WheelchairFolding and Unfolding Wheelchair Sling Seat Model Wheelchairs Unfolding Folding Recliners onlySling Seat Model Wheelchairs Folding Solid Seat Model WheelchairsA T U R E S FeaturesFeatures Specifications SpecificationsHandling PackagingC K a G I N G N D L I N GSafety Inspection Check List Safety Inspection ChecklistI N T E N a N C E TroubleshootingMaintenance Installing Footrests Figure Procedure Front RiggingsAdjusting Footrest Height Pivot Slide Tube Height Adjustment FigureInstalling Elevating Legrests Figure Installing 3-INCH Extension FigureProcedure Raising/Lowering Elevating LegrestsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjusting CalfpadsInstalling Adjustable Angle Flip-up Footplates Figure Adjustable Angle Flip-up Footplate Depth Adjustment FigureReplacing Sector Block Figure Optional Footrest AccessoriesFLIP-UP Footplates Figure Aluminum or Composite Footplates FigureM S Procedure ArmsInstalling Removing Adjusting the T ArmsHeight Figure Width FigureArm Hex Screws Washers Reposition the arm tube on the T arm postArm Sockets Figure Replacing the Locking Lever T Arms Figure Arms ProcedureTop Middle Bottom Side Arm Guard Socket Screws Bottom ClampCorresponding Arm Adjustment to Back Angle Figures 10 Using FigureInstalling/Height Adjustment Figure Replacement AdjustmentAngled Portion Cantilever Arm Locking Mechanism Actuator Apply LoctiteAdjusting Conventional Arm Height Installing Fabric Clothing Guards FigureInstalling Rigid Side Guards Figure Removing Conventional ArmsFront Arm Sockets Figure Replacing Armrest Pads FigureRear Arm Sockets Figure Installing Adjustable Back Upholstery Figure Procedure BackC K Replacing Back UpholsteryAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureBack upholstery cover is designed for three 3 reasons WHY USE Adjustable Back Upholstery a Clinical DiscussionBack Upholstery Cover Adjustable Height Backs Figure Adjusting the Back HeightRecliner Back Upholstery Figure Recliner Headrest Upholstery FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Fixed Height Backs FigureSlowly remove the two 2 backs canes from the wheelchair Replacing the Locking Mechanism in the Back Cane Figure Repositioning the Back Changing Seat Depth Changing the Back AngleBack Plate Non-Recliners FigureRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherReplacing Folding Push Handle Recliners only Figure Installing and Removing a Seating SystemRecliner Brackets Seat A TCHANGING/REPOSITIONING Seat Rails Figure Replacing Seat Upholstery FigureRepositioning the Crossbraces Figure Procedure SeatChanging Seat Width Standard Folding Frames FigurePivot Link For installation of newCrossbraces Folding Frames Without Seat Rails FigureCrossmembers Wheelchair Frame Washer Hex Screws Hex Bolt Seat Width HolesRigid Frames Figure Replacing Front Fork Figure S T E R SCasters Casters REPLACING/REPAIRING Front Caster TIRE/TUBEInline Caster Headtubes Figure Offset Caster Headtubes FigureHeight Adjustment Caster Headtube Mounting Adjustments FigureRepositioning the Caster Headtubes Inline Caster Headtube Hardware OffsetCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Installing QUICK-RELEASE Casters FigureDust Release Detent Pin Adjusting the QUICK-RELEASE Axle Figure REMOVING/INSTALLING Rear Wheels FigureA R Rear WheelsAdjusting the QUAD-RELEASE Handle Figure Installing the QUAD-RELEASE Axle FigureJusting the QUAD-RELEASE Handle And/or OutRemoving the Play From the Rear Wheels Handrim Replacement FigureSpoke Rear Wheels Phillips Bolt HandrimComposite Rear Wheels Figure Installing Projection HandrimsComposite Rim Locknut Spoke Rear Wheels FigureAdjusting the Wheelbase Length Figure REPAIRING/REPLACING Rear Wheel TIRE/ TubeJam Nuts Shortening ForwardAdjusting Rear Wheel Height Figure Adjusting the Wheelbase Width FigureAxle Mounting PlateWheel Lock Extension Handle Installation Figure Adjusting the Wheel Locks FigureE E L K S E R S Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Procedure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Installing the Anti-Tippers FigureRecliner REPLACEMENT/ADJUSTMENTRecliner Operation Figures 1 Folding/Unfolding the WheelchairActuator Housing Cable Locking Nut Installing New Recliner CablesRecliner Trigger Release LeverMust Look TOO LOW Replacing the GAS Cylinders FigureLike this Steps 1, 5Trigger Release Lever Cable Locking Nut Adjusting Adjusting the GAS Cylinders FigureSqueeze the handles to extend the new gas cylinders Detail B Must Look TOO LOWSEAT-TO-FLOOR Height Determination SEAT-TO-FLOORMinus EqualsStandard MULTI-POSITION Axle Plate Procedure SEAT-TO-FLOORChanging SEAT-TO-FLOOR Height A T Frame Inline Caster Headtube Front SEAT-TO-FLOOR HeightsLower Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth Determination Figure A T P T HChanging Seat Depth Seat DepthSeat Depth Seat Depth ChecklistLeft A T P TRight Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page R R a N T Y Limited WarrantyLimited Warranty One Invacare Way Technical Support