Invacare 1061057 Replacing Armrest Pads Figure, Rear Arm Sockets Figure, Front Arm Sockets Figure

Page 27

ARMS

PROCEDURE 2

Height

Locked (DOWN -

VERTICAL)

Adjustment

 

Lever

 

Unlocked (UP-

HORIZONTAL)

Armrest Release

Lever

FIGURE 16 - ADJUSTING CONVENTIONAL ARM HEIGHT, REMOVING OR REPLACING CONVENTIONAL ARMS

REPLACING ARMREST PADS (FIGURE 17)

1.Remove the phillips screws that secure the arm- rest pad to the armrest assembly.

2.Replace armrest pad and securely tighten with the existing phillips screws.

Armrest Pad

Phillips Screws

Armrest Assembly

FIGURE 17 - REPLACING ARMREST PADS

REPOSITIONING THE CONVENTIONAL ARMS

NOTE: Conventional arms can only be repositioned on medium and long frame wheelchairs. There is only one (1) position for conventional arms on short frame wheelchairs.

Rear Arm Sockets (FIGURE 18)

1.Determine the necessary rear arm socket position for the necessary seat depth. Refer to CHANGING SEAT DEPTHS in PROCEDURE 10 of this manual.

2.Remove the hex bolt, washer and locknut that se- cure the rear arm socket, nylon shim and rear arm socket mount to the wheelchair frame.

3.Move the rear arm socket, nylon shim and rear arm socket mount to the position determined in STEP 1.

4.Reinstall the rear arm socket, nylon shim and rear arm socket mount onto the wheelchair with the hex bolt, washer and locknut. Refer to FIGURE 13 for correct orientation.

5.Repeat STEPS 1-4for the opposite side of the wheel- chair.

 

 

Rear Arm Socket

 

 

 

Hex Bolt

 

 

 

Nylon

 

 

 

Shim

 

 

 

Rear Arm

 

 

Wheelchair

Socket

 

 

Mount

 

Washer

Frame

 

 

Locknut

 

 

 

 

 

FIGURE 18 - REPOSITIONING THE

CONVENTIONAL ARMS - REAR ARM SOCKETS

Front Arm Sockets (FIGURE 19)

1.Determine the necessary front arm socket and seat guide position for the necessary seat depth. Refer to CHANGING SEAT DEPTHS in PROCEDURE 10 of this manual.

2.Remove the socket bolts and locknuts that secure the front arm socket and seat guide to the wheel- chair.

3.Move the front arm socket and seat guide to the position determined in STEP 1.

4.Resecure the front arm socket and seat guide to the wheelchair with the socket bolts and locknuts.

5.Repeat STEPS 1-4for the opposite side of the wheel- chair.

Socket Bolt

Socket Bolt

Front Arm

Socket

 

Seat Guide

 

Wheelchair

Locknut

Frame

 

FIGURE 19 - REPOSITIONING THE

CONVENTIONAL ARMS - FRONT ARM SOCKETS

A R M S

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysRecliners Percentage of Weight DistributionUnoccupied Occupied NON-RECLINERSSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Solid Seat Model Wheelchairs Recliners onlySling Seat Model Wheelchairs Unfolding Folding Sling Seat Model Wheelchairs FoldingFeatures FeaturesA T U R E S Specifications SpecificationsN D L I N G PackagingHandling C K a G I N GSafety Inspection Check List Safety Inspection ChecklistTroubleshooting MaintenanceI N T E N a N C E Pivot Slide Tube Height Adjustment Figure Procedure Front RiggingsInstalling Footrests Figure Adjusting Footrest HeightRaising/Lowering Elevating Legrests Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure ProcedureAdjustable Angle Flip-up Footplate Depth Adjustment Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Installing Adjustable Angle Flip-up Footplates FigureAluminum or Composite Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure FLIP-UP Footplates FigureProcedure Arms InstallingM S Width Figure Adjusting the T ArmsRemoving Height FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Socket Screws Bottom Clamp Arms ProcedureReplacing the Locking Lever T Arms Figure Top Middle Bottom Side Arm GuardUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Locking Mechanism Actuator Apply Loctite AdjustmentReplacement Angled Portion Cantilever ArmRemoving Conventional Arms Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Installing Rigid Side Guards FigureReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure Replacing Back Upholstery Procedure BackInstalling Adjustable Back Upholstery Figure C KAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Recliner Headrest Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Back Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Non-Recliners Figure Changing the Back AngleRepositioning the Back Changing Seat Depth Back PlateRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure Replacing Seat Upholstery Figure A TSeat CHANGING/REPOSITIONING Seat Rails FigureStandard Folding Frames Figure Procedure SeatRepositioning the Crossbraces Figure Changing Seat WidthFolding Frames Without Seat Rails Figure For installation of newPivot Link CrossbracesHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure Offset Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Inline Caster Headtubes FigureInline Caster Headtube Hardware Offset Caster Headtube Mounting Adjustments FigureHeight Adjustment Repositioning the Caster HeadtubesInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Rear Wheels REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure A RAnd/or Out Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure Justing the QUAD-RELEASE HandlePhillips Bolt Handrim Handrim Replacement FigureRemoving the Play From the Rear Wheels Spoke Rear WheelsSpoke Rear Wheels Figure Installing Projection HandrimsComposite Rear Wheels Figure Composite Rim LocknutShortening Forward REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Jam NutsMounting Plate Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure AxleWheel LOCKS/ANTI-TIPPERS Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure E E L K S E R SInstalling the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Adjusting the Anti-Tippers FigureFolding/Unfolding the Wheelchair REPLACEMENT/ADJUSTMENTRecliner Recliner Operation Figures 1Trigger Release Lever Installing New Recliner CablesActuator Housing Cable Locking Nut ReclinerSteps 1, 5 Replacing the GAS Cylinders FigureMust Look TOO LOW Like thisDetail B Must Look TOO LOW Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Squeeze the handles to extend the new gas cylindersEquals SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination MinusProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth A T P T HSeat Depth Determination Figure Changing Seat DepthSeat Depth Seat Depth ChecklistRear Mounting Hole A T P TLeft RightApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents