Invacare 1061057, 96-100 manual A T

Page 59

SEAT-TO-FLOOR

PROCEDURE 9

AXLE MOUNTING PLATE POSITIONS FOR 20, 22 or 24-INCH REAR WHEELS

Refer to the following figures to determine the obtainable rear seat-to-floor height for 20, 22 or 24-inch rear wheels:

NOTE: The rear seat-to-floor heights are based on pneumatic tires and pneumatic tires with flat free inserts. If wheelchair is equipped with urethane tires, subtract 1/4-inch from the measure- ments listed below. All heights are approximate to +1/4-inch due to tire wear and air pressure.

NOTE: The following charts are shown with non-recliner back hardware only for clarity. The axle mounting positions are the same for recliner wheelchairs.

S E A T

T O

REAR	REAR	AXLE PLATE POSITION
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT
20	14-3/4-INCHES
22	15-3/4-INCHES
24	16-1/2-INCHES
REAR	REAR	AXLE PLATE POSITION
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT
20	16-INCHES
22	17-INCHES
24	17-3/4-INCHES

REAR	REAR	AXLE PLATE POSITION
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT
20	15-1/2-INCHES
22	16-1/2-INCHES
24	17-1/4-INCHES
REAR	REAR	AXLE PLATE POSITION
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT
20	16-3/4-INCHES
22	17-3/4-INCHES
24	18-1/2-INCHES

F L O O R

REAR	REAR
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT

2017-1/4-INCHES

2218-1/4-INCHES

2419-INCHES

AXLE PLATE POSITION

REAR	REAR
WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT
20	18-INCHES

2219-INCHES

2419-3/4-INCHES

AXLE PLATE POSITION

REAR	REAR	AXLE PLATE POSITION	REAR	REAR	AXLE PLATE POSITION
WHEEL	SEAT-TO-		WHEEL	SEAT-TO-
SIZE	FLOOR HEIGHT		SIZE	FLOOR HEIGHT
20	18-1/2-INCHES		20	19-1/4-INCHES
22	19-1/2-INCHES		22	20-1/4-INCHES
24	20-1/4-INCHES		24	21-INCHES
			59

Image 59

Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysRecliners Percentage of Weight DistributionUnoccupied Occupied NON-RECLINERSBending Forward SAFETY/HANDLING Functional Reach from a WheelchairFolding and Unfolding Wheelchair Solid Seat Model Wheelchairs Recliners onlySling Seat Model Wheelchairs Unfolding Folding Sling Seat Model Wheelchairs FoldingA T U R E S FeaturesFeatures Specifications SpecificationsN D L I N G PackagingHandling C K a G I N GSafety Inspection Check List Safety Inspection ChecklistI N T E N a N C E TroubleshootingMaintenance Pivot Slide Tube Height Adjustment Figure Procedure Front RiggingsInstalling Footrests Figure Adjusting Footrest HeightRaising/Lowering Elevating Legrests Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure ProcedureAdjustable Angle Flip-up Footplate Depth Adjustment Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Installing Adjustable Angle Flip-up Footplates FigureAluminum or Composite Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure FLIP-UP Footplates FigureM S Procedure ArmsInstalling Width Figure Adjusting the T ArmsRemoving Height FigureArm Hex Screws Washers Reposition the arm tube on the T arm postArm Sockets Figure Socket Screws Bottom Clamp Arms ProcedureReplacing the Locking Lever T Arms Figure Top Middle Bottom Side Arm GuardCorresponding Arm Adjustment to Back Angle Figures 10 Using FigureInstalling/Height Adjustment Figure Locking Mechanism Actuator Apply Loctite AdjustmentReplacement Angled Portion Cantilever ArmRemoving Conventional Arms Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Installing Rigid Side Guards FigureFront Arm Sockets Figure Replacing Armrest Pads FigureRear Arm Sockets Figure Replacing Back Upholstery Procedure BackInstalling Adjustable Back Upholstery Figure C KAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureBack upholstery cover is designed for three 3 reasons WHY USE Adjustable Back Upholstery a Clinical DiscussionBack Upholstery Cover Recliner Headrest Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Back Upholstery FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Fixed Height Backs FigureSlowly remove the two 2 backs canes from the wheelchair Replacing the Locking Mechanism in the Back Cane Figure Non-Recliners Figure Changing the Back AngleRepositioning the Back Changing Seat Depth Back PlateRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherReplacing Folding Push Handle Recliners only Figure Installing and Removing a Seating SystemRecliner Brackets Replacing Seat Upholstery Figure A TSeat CHANGING/REPOSITIONING Seat Rails FigureStandard Folding Frames Figure Procedure SeatRepositioning the Crossbraces Figure Changing Seat WidthFolding Frames Without Seat Rails Figure For installation of newPivot Link CrossbracesCrossmembers Wheelchair Frame Washer Hex Screws Hex Bolt Seat Width HolesRigid Frames Figure Replacing Front Fork Figure S T E R SCasters Offset Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Inline Caster Headtubes FigureInline Caster Headtube Hardware Offset Caster Headtube Mounting Adjustments FigureHeight Adjustment Repositioning the Caster HeadtubesCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Installing QUICK-RELEASE Casters FigureDust Release Detent Pin Rear Wheels REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure A RAnd/or Out Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure Justing the QUAD-RELEASE HandlePhillips Bolt Handrim Handrim Replacement FigureRemoving the Play From the Rear Wheels Spoke Rear WheelsSpoke Rear Wheels Figure Installing Projection HandrimsComposite Rear Wheels Figure Composite Rim LocknutShortening Forward REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Jam NutsMounting Plate Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure AxleWheel LOCKS/ANTI-TIPPERS Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure E E L K S E R SInstalling the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Adjusting the Anti-Tippers FigureFolding/Unfolding the Wheelchair REPLACEMENT/ADJUSTMENTRecliner Recliner Operation Figures 1Trigger Release Lever Installing New Recliner CablesActuator Housing Cable Locking Nut ReclinerSteps 1, 5 Replacing the GAS Cylinders FigureMust Look TOO LOW Like thisDetail B Must Look TOO LOW Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Squeeze the handles to extend the new gas cylindersEquals SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination MinusStandard MULTI-POSITION Axle Plate Procedure SEAT-TO-FLOORChanging SEAT-TO-FLOOR Height A T Frame Inline Caster Headtube Front SEAT-TO-FLOOR HeightsLower Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth A T P T HSeat Depth Determination Figure Changing Seat DepthSeat Depth Seat Depth ChecklistRear Mounting Hole A T P TLeft RightApproximate 2-inch gap A T P T Inch Right A T P T H Page R R a N T Y Limited WarrantyLimited Warranty One Invacare Way Technical Support