Invacare 96-100, 1061057 manual SAFETY/HANDLING of Wheelchairs

Page 6

SAFETY/HANDLING

SAFETY/HANDLING OF WHEELCHAIRS

S A F E T Y

&

H A N D L I N G

“Safety and Handling” of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and main- tenance of the wheelchair. It is important to practice and master these safe techniques until you are comfortable in maneuvering around the frequently encountered ar- chitectural barriers.

Use this information only as a “basic” guide. The tech- niques that are discussed on the following pages have been used successfully by many.

Individual wheelchair users often develop skills to deal with daily living activities that may differ from those de- scribed in this manual. Invacare recognizes and encour- ages each individual to try what works best for him/her in overcoming architectural obstacles that they may encoun- ter. Techniques in this manual are a starting point for the new wheelchair user and assistant with “safety” as the most important consideration for all.

STABILITY AND BALANCE

WARNING

ALWAYS wear your seat restraint. Inasmuch as the SEAT RESTRAINT is an option on this wheelchair (You may order with or without the seat restraint), Invacare strongly recommends ordering the seat restraint as an additional safeguard for the wheel- chair user.

To assure stability and proper operation of your wheel- chair, you must at all times wear your seat restraint and maintain proper balance. Your wheelchair has been de- signed to remain upright and stable during normal daily activities as long as you do not move beyond the center of gravity.

DO NOT lean forward out of the wheelchair any further than the length of the armrests. Make sure the casters are pointing in the forward position whenever you lean forward. This can be achieved by advancing the wheel- chair and then reversing it in a straight line.

A NOTE TO WHEELCHAIR ASSISTANTS

When assistance to the wheelchair user is required, re- member to use good body mechanics. Keep your back straight and bend your knees whenever tilting the wheel- chair or traversing curbs, or other impediments.

Also, be aware of any removable (detachable) parts. These must NEVER be used for hand-held or lifting sup- ports, as they may be inadvertently released, resulting in possible injury to the user and/or assistant(s).

When learning a new assistance technique, have an ex- perienced assistant help you before attempting it alone.

TILTING

WARNING

DO NOT tilt the wheelchair without assistance.

When tilting the wheelchair, an assistant should grasp the back of the wheelchair on a non-removable (non- detachable) part. Inform the wheelchair occupant before tilting the wheelchair and remind him/her to lean back. Be sure the occupant’s feet and hands are clear of all wheels.

TILTING - CURBS:

After mastering the techniques of tilting the wheelchair, use this procedure to tackle curbs, short stairs, etc.

Method 1 - Wheelchairs With Step Tubes

Apply a continuous downward motion until the balance point is achieved and the front casters clear the curb. At this point, the assistant will feel a difference in the weight distribution.

Roll the wheelchair forward and slowly lower the wheel- chair in one continuous movement onto the sidewalk. Do not let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant. Push the wheelchair forward until the rear wheels roll up and over the curb.

COPING WITH EVERYDAY OBSTACLES

Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair. Keep in mind your center of gravity to main- tain stability and balance.

METHOD 1 - WHEELCHAIR WITH STEP TUBES

Method 2 - Wheelchairs Without Step Tubes

Unless the first assistant has exceptional upper body strength, it is recommended that METHOD 2 use two (2) assistants.

6

Image 6
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsNON-RECLINERS Percentage of Weight DistributionUnoccupied Occupied ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Sling Seat Model Wheelchairs Folding Recliners onlySling Seat Model Wheelchairs Unfolding Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsC K a G I N G PackagingHandling N D L I N GSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceI N T E N a N C E Adjusting Footrest Height Procedure Front RiggingsInstalling Footrests Figure Pivot Slide Tube Height Adjustment FigureProcedure Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure Raising/Lowering Elevating LegrestsInstalling Adjustable Angle Flip-up Footplates Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjustable Angle Flip-up Footplate Depth Adjustment FigureFLIP-UP Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Height Figure Adjusting the T ArmsRemoving Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Top Middle Bottom Side Arm Guard Arms ProcedureReplacing the Locking Lever T Arms Figure Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Angled Portion Cantilever Arm AdjustmentReplacement Locking Mechanism Actuator Apply LoctiteInstalling Rigid Side Guards Figure Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure C K Procedure BackInstalling Adjustable Back Upholstery Figure Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Recliner Back Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Back Plate Changing the Back AngleRepositioning the Back Changing Seat Depth Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure CHANGING/REPOSITIONING Seat Rails Figure A TSeat Replacing Seat Upholstery FigureChanging Seat Width Procedure SeatRepositioning the Crossbraces Figure Standard Folding Frames FigureCrossbraces For installation of newPivot Link Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure Inline Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Offset Caster Headtubes FigureRepositioning the Caster Headtubes Caster Headtube Mounting Adjustments FigureHeight Adjustment Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw A R REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure Rear WheelsJusting the QUAD-RELEASE Handle Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure And/or OutSpoke Rear Wheels Handrim Replacement FigureRemoving the Play From the Rear Wheels Phillips Bolt HandrimComposite Rim Locknut Installing Projection HandrimsComposite Rear Wheels Figure Spoke Rear Wheels FigureJam Nuts REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Shortening ForwardAxle Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure Mounting PlateE E L K S E R S Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the Anti-Tippers FigureRecliner Operation Figures 1 REPLACEMENT/ADJUSTMENTRecliner Folding/Unfolding the WheelchairRecliner Installing New Recliner CablesActuator Housing Cable Locking Nut Trigger Release LeverLike this Replacing the GAS Cylinders FigureMust Look TOO LOW Steps 1, 5Squeeze the handles to extend the new gas cylinders Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Detail B Must Look TOO LOWMinus SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Changing Seat Depth A T P T HSeat Depth Determination Figure Seat DepthSeat Depth Checklist Seat DepthRight A T P TLeft Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support