Invacare 96-100, 1061057 manual Reposition the arm tube on the T arm post, Arm Sockets Figure

Page 22

PROCEDURE 2

ARMS

 

 

 

A R M S

3.Reposition the arm tube on the "T" arm post:

A.Desk Length Arms - to one (1) of three (3) posi- tions depending on the desired arm pad depth.

B.Full Length Arms - to one (1) of five (5) posi- tions depending on the desired arm pad depth.

NOTE: Additional positions are obtainable by turn- ing the arm tube 180o.

4.Re-secure the arm tube to the "T" arm post with the two (2) socket screws.

5.Reattach the arm pad to the arm tube with the two

(2) phillips screws.

6.Repeat for the opposite side, if necessary.

6.Squeeze the "T" arm socket together until the socket is flush with the "T" arm.

7.While holding the "T" arm socket together, tighten the four (4) hex screws and washers securely.

8.Press in on the locking lever and lift the "T" arm straight up and out of the "T" arm socket.

9.Repeat STEPS 5-7, if necessary until the "T" arm slides in the "T" arm socket as desired.

10.Reinstall the "T" arm socket onto the wheelchair. Refer to INSTALLING THE "T" ARM SOCKETS in this section of the manual.

Hex Screws

Optional Locking Pins

Socket

Screws

Phillips

Screw

"T" Arm

Post

Arm Pad

Arm Tube

NOTE: If

necessary, turn arm tube 180o to obtain two

(2)positions.

Phillips Screw

Wheelchair Frame

Washers

"T" Arm Clamp

"T" Arm Socket

FIGURE 5 - ADJUSTING THE "T" ARMS -

DEPTH

"T" Arm Sockets (FIGURE 6)

1.Remove the rear wheels from the wheelchair. If nec- essary, refer to the owner's manual supplied with the wheelchair.

2.Remove the three (3) hex screws and washers that secure the "T" arm socket and "T" arm clamp to the wheelchair frame and remove the "T" arm socket from the wheelchair.

3.If equipped with optional locking pins, remove the locking pins that secure the "T" arm socket to the wheelchair frame.

4.Loosen, but do not remove the four (4) hex screws and washers that secure the "T" arm socket together.

NOTE: The "T" arm socket will disassemble if the four (4) hex screws and washers are removed.

5.Slide the "T" arm into the "T" arm socket until the lock lever is in the slot in the "T" arm socket and an au- dible "click" is heard.

"T" Arm

Hex Screws

and Washers

"T" Arm

Hex Screws

Socket

and Washers

FIGURE 6 - ADJUSTING THE "T" ARMS - "T"

ARM SOCKETS

ADJUSTING THE TRANSFER ASSISTS AND/ OR SIDE GUARDS - "T" ARMS (FIGURE 7)

1.Remove the "T" arm from the wheelchair. Refer to INSTALLING/REMOVING THE "T" ARMS in this section of the manual.

2.Remove the bottom socket screw that secures the side guard to the bottom clamp.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsNON-RECLINERS Percentage of Weight DistributionUnoccupied Occupied ReclinersFolding and Unfolding Wheelchair SAFETY/HANDLING Functional Reach from a WheelchairBending Forward Sling Seat Model Wheelchairs Folding Recliners onlySling Seat Model Wheelchairs Unfolding Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsC K a G I N G PackagingHandling N D L I N GSafety Inspection Checklist Safety Inspection Check ListMaintenance TroubleshootingI N T E N a N C E Adjusting Footrest Height Procedure Front RiggingsInstalling Footrests Figure Pivot Slide Tube Height Adjustment FigureProcedure Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure Raising/Lowering Elevating LegrestsInstalling Adjustable Angle Flip-up Footplates Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjustable Angle Flip-up Footplate Depth Adjustment FigureFLIP-UP Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure Aluminum or Composite Footplates FigureInstalling Procedure ArmsM S Height Figure Adjusting the T ArmsRemoving Width FigureArm Sockets Figure Reposition the arm tube on the T arm postArm Hex Screws Washers Top Middle Bottom Side Arm Guard Arms ProcedureReplacing the Locking Lever T Arms Figure Socket Screws Bottom ClampInstalling/Height Adjustment Figure Using FigureCorresponding Arm Adjustment to Back Angle Figures 10 Angled Portion Cantilever Arm AdjustmentReplacement Locking Mechanism Actuator Apply LoctiteInstalling Rigid Side Guards Figure Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Removing Conventional ArmsRear Arm Sockets Figure Replacing Armrest Pads FigureFront Arm Sockets Figure C K Procedure BackInstalling Adjustable Back Upholstery Figure Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsBack Upholstery Cover WHY USE Adjustable Back Upholstery a Clinical DiscussionBack upholstery cover is designed for three 3 reasons Recliner Back Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Headrest Upholstery FigureSlowly remove the two 2 backs canes from the wheelchair Fixed Height Backs FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Back Plate Changing the Back AngleRepositioning the Back Changing Seat Depth Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureRecliner Brackets Installing and Removing a Seating SystemReplacing Folding Push Handle Recliners only Figure CHANGING/REPOSITIONING Seat Rails Figure A TSeat Replacing Seat Upholstery FigureChanging Seat Width Procedure SeatRepositioning the Crossbraces Figure Standard Folding Frames FigureCrossbraces For installation of newPivot Link Folding Frames Without Seat Rails FigureRigid Frames Figure Hex Bolt Seat Width HolesCrossmembers Wheelchair Frame Washer Hex Screws Casters S T E R SReplacing Front Fork Figure Inline Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Offset Caster Headtubes FigureRepositioning the Caster Headtubes Caster Headtube Mounting Adjustments FigureHeight Adjustment Inline Caster Headtube Hardware OffsetDust Release Detent Pin Installing QUICK-RELEASE Casters FigureCover Headtube Locknut Cap Spacer Fork Stem Hex Screw A R REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure Rear WheelsJusting the QUAD-RELEASE Handle Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure And/or OutSpoke Rear Wheels Handrim Replacement FigureRemoving the Play From the Rear Wheels Phillips Bolt HandrimComposite Rim Locknut Installing Projection HandrimsComposite Rear Wheels Figure Spoke Rear Wheels FigureJam Nuts REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Shortening ForwardAxle Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure Mounting PlateE E L K S E R S Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the Anti-Tippers FigureRecliner Operation Figures 1 REPLACEMENT/ADJUSTMENTRecliner Folding/Unfolding the WheelchairRecliner Installing New Recliner CablesActuator Housing Cable Locking Nut Trigger Release LeverLike this Replacing the GAS Cylinders FigureMust Look TOO LOW Steps 1, 5Squeeze the handles to extend the new gas cylinders Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Detail B Must Look TOO LOWMinus SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination EqualsChanging SEAT-TO-FLOOR Height Procedure SEAT-TO-FLOORStandard MULTI-POSITION Axle Plate A T Lower Inline Caster Headtube Front SEAT-TO-FLOOR HeightsFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Changing Seat Depth A T P T HSeat Depth Determination Figure Seat DepthSeat Depth Checklist Seat DepthRight A T P TLeft Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents