Invacare 1061057 manual Adjusting the T Arms, Removing, Height Figure, Width Figure, Depth Figure

Page 21

ARMS

PROCEDURE 2

Removing

1.Press in on the locking lever and lift the "T" arm straight up and out of the "T" arm socket.

NOTE: If the "T" arm does not slide up and down in the "T" arm socket as desired, adjust the "T" arm socket. Refer to ADJUSTING THE "T" ARMS in this section of the manual.

2.Repeat STEP 2 for the opposite side of the wheel- chair.

"T" Arm

Wheelchair

 

Frame

Locking Lever

 

 

(Towards the

"T" Arm

front of the

wheelchair.)

Socket

 

 

Slot

FIGURE 2 - INSTALLING/REMOVING THE "T"

ARMS

ADJUSTING THE "T" ARMS

Height (FIGURE 3)

1.Unlock the "T" arm by flipping the "T" arm release lever towards the inside of the wheelchair.

NOTE: If necessary, Pull out on the "T" arm re- lease lever and rotate 180o so it can be flipped towards the outside of the wheelchair.

2.Slide the "T" arm to one (1) of:

A.Low Height "T" Arms - Nine (9) positions.

B.High Height "T" Arms - Seven (7) positions.

NOTE: If the inside "T" arm post does not slide up and down in the outside "T" arm post as desired, perform one (1) of the following:

A.Tighten - Tightening the set screws on the out- side "T" arm post will make it harder to move the inside "T" arm post up and down.

B.Loosen - Loosening the set screws on the out- side "T" arm post will make it easier to move the inside "T" arm post up and down.

3.Lock the "T" arm by flipping the "T" arm release lever towards the front of the wheelchair.

"T" Arm Release

Lever - Unlocked

Position

Inside "T"

Set

Arm Post

Screws

Outside "T"

Arm Post

"T" Arm Release Lever -

Locked Position

FIGURE 3 - ADJUSTING THE "T" ARMS -

HEIGHT

Width (FIGURE 4)

1.Remove the two (2) phillips screws that secure the arm pad to the arm tube.

2.Turn the arm pad around and reposition the arm pad on the arm tube.

3.Re-secure the arm pad to the arm tube with the two

(2) phillips screws.

4.Repeat for the opposite side, if necessary.

Arm Pad

 

Arm Tube

Phillips

Phillips Screw

Screw

 

FIGURE 4 - ADJUSTING THE "T" ARMS -

WIDTH

Depth (FIGURE 5)

1.Remove the two (2) phillips screws that secure the arm pad to the arm tube.

2.Remove the two (2) socket screws that secure the arm tube to the "T" arm post.

A R M S

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummaryRecliner Option only Safety SummarySAFETY/HANDLING of Wheelchairs Transferring to and from Other Seats StairwaysUnoccupied Occupied Percentage of Weight DistributionNON-RECLINERS ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Sling Seat Model Wheelchairs Unfolding Folding Recliners onlySling Seat Model Wheelchairs Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsHandling PackagingC K a G I N G N D L I N GSafety Inspection Check List Safety Inspection ChecklistTroubleshooting MaintenanceI N T E N a N C E Installing Footrests Figure Procedure Front RiggingsAdjusting Footrest Height Pivot Slide Tube Height Adjustment FigureInstalling Elevating Legrests Figure Installing 3-INCH Extension FigureProcedure Raising/Lowering Elevating LegrestsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjusting CalfpadsInstalling Adjustable Angle Flip-up Footplates Figure Adjustable Angle Flip-up Footplate Depth Adjustment FigureReplacing Sector Block Figure Optional Footrest AccessoriesFLIP-UP Footplates Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Removing Adjusting the T ArmsHeight Figure Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Replacing the Locking Lever T Arms Figure Arms ProcedureTop Middle Bottom Side Arm Guard Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Replacement AdjustmentAngled Portion Cantilever Arm Locking Mechanism Actuator Apply LoctiteAdjusting Conventional Arm Height Installing Fabric Clothing Guards FigureInstalling Rigid Side Guards Figure Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure Installing Adjustable Back Upholstery Figure Procedure BackC K Replacing Back UpholsteryAdjustable Tension Straps Replacing Adjustable Back Upholstery FigureWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Adjustable Height Backs Figure Adjusting the Back HeightRecliner Back Upholstery Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Repositioning the Back Changing Seat Depth Changing the Back AngleBack Plate Non-Recliners FigureRecliners Figure Back Angle Plate Hex Bolt Locknut Wheelchair Frame WasherInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure Seat A TCHANGING/REPOSITIONING Seat Rails Figure Replacing Seat Upholstery FigureRepositioning the Crossbraces Figure Procedure SeatChanging Seat Width Standard Folding Frames FigurePivot Link For installation of newCrossbraces Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure Casters REPLACING/REPAIRING Front Caster TIRE/TUBEInline Caster Headtubes Figure Offset Caster Headtubes FigureHeight Adjustment Caster Headtube Mounting Adjustments FigureRepositioning the Caster Headtubes Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Adjusting the QUICK-RELEASE Axle Figure REMOVING/INSTALLING Rear Wheels FigureA R Rear WheelsAdjusting the QUAD-RELEASE Handle Figure Installing the QUAD-RELEASE Axle FigureJusting the QUAD-RELEASE Handle And/or OutRemoving the Play From the Rear Wheels Handrim Replacement FigureSpoke Rear Wheels Phillips Bolt HandrimComposite Rear Wheels Figure Installing Projection HandrimsComposite Rim Locknut Spoke Rear Wheels FigureAdjusting the Wheelbase Length Figure REPAIRING/REPLACING Rear Wheel TIRE/ TubeJam Nuts Shortening ForwardAdjusting Rear Wheel Height Figure Adjusting the Wheelbase Width FigureAxle Mounting PlateWheel Lock Extension Handle Installation Figure Adjusting the Wheel Locks FigureE E L K S E R S Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Procedure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Installing the Anti-Tippers FigureRecliner REPLACEMENT/ADJUSTMENTRecliner Operation Figures 1 Folding/Unfolding the WheelchairActuator Housing Cable Locking Nut Installing New Recliner CablesRecliner Trigger Release LeverMust Look TOO LOW Replacing the GAS Cylinders FigureLike this Steps 1, 5Trigger Release Lever Cable Locking Nut Adjusting Adjusting the GAS Cylinders FigureSqueeze the handles to extend the new gas cylinders Detail B Must Look TOO LOWSEAT-TO-FLOOR Height Determination SEAT-TO-FLOORMinus EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Seat Depth Determination Figure A T P T HChanging Seat Depth Seat DepthSeat Depth Seat Depth ChecklistLeft A T P TRight Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents