Invacare 96-100, 1061057 manual Using Figure, Installing/Height Adjustment Figure

Page 24

PROCEDURE 2

ARMS

 

 

 

A R M S

USING/INSTALLING/HEIGHT ADJUSTMENT/CORRESPONDING ARM ADJUSTMENT TO BACK ANGLE - CANTILEVER ARMS

NOTE: The cantilever arms are designed for use with the fixed height back canes only.

Using (FIGURE 9)

1.Pull the actuator of the locking mechanism towards the front of the wheelchair.

2.While holding the actuator of the locking mecha- nism, pull up on the cantilever arm.

NOTE: If necessary, the locking mechanism in the cantilever arm can be repositioned so the cantilever arm will open down instead of up. Refer to REPLAC-

ING/REPOSITIONING THE LOCKING MECHANISM IN THE CANTILEVER ARM in this section of the manual.

3.To lock the cantilever arm, push down until there is an audible click.

4.Pull up on the cantilever arm to make sure it is locked in place.

Installing/Height Adjustment (FIGURE 9)

NOTE: When removing the locknuts and washers from the cantilever arm assembly, leave the top hex bolt, coved washers and spacer (between ad- justment plate and cantilever arm) in place.

2.Slide the bottom hex bolt (w/coved washer) through the adjustment plate and back cane.

3.Securely tighten the cantilever arm to the wheelchair with two (2) locknuts and washers.

4.Adjust the angle of the cantilever arm, if necessary. Refer to CORRESPONDING ARM ADJUSTMENT TO BACK ANGLE in this section of the manual.

Corresponding Arm Adjustment to Back Angle (FIGURES 10 and 11)

NOTE: This adjustment is recommended if the back angle has been changed to keep arm parallel to the ground/floor.

1.Flip the cantilever arm up and out of the way.

2.Remove the locknut that secures the locking pin to the adjustment plate (FIGURE 10).

Adjustment Plate

 

Locking Pin

Locknut

 

Washer

FIGURE 10 - ADJUSTING THE CANTILEVER ARMS

1.Slide the partially assembled cantilever arm assembly w/mounting hardware through the back cane. Make sure the adjustment plate is towards the inside of the wheelchair.

NOTE: This includes top hex bolt, coved washers and spacer (between adjustment plate and cantile- ver arm).

Coved Washers

Adjustment Plate

Back Cane

Spacer

Actuator

Locknuts

Washers

Top Hex Bolt

and Coved Washer

80O

Back Plate

Arm Plate

85O

Back Plate

Arm Plate

90O

Back Plate

Arm Plate

95O

Back Plate

Arm Plate

100O

Back Plate

Arm Plate

105O AND 110O

Back Plate

Arm Plate

Bottom Hex Bolt

Cantilever Arm

FIGURE 9- USING/INSTALLING/HEIGHT ADJUSTMENT - CANTILEVER ARMS

FIGURE 11 - CORRESPONDING ARM ADJUSTMENT TO BACK ANGLE - CANTILEVER ARMS

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsPercentage of Weight Distribution Unoccupied OccupiedNON-RECLINERS ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Recliners only Sling Seat Model Wheelchairs Unfolding FoldingSling Seat Model Wheelchairs Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsPackaging HandlingC K a G I N G N D L I N GSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceI N T E N a N C E Procedure Front Riggings Installing Footrests FigureAdjusting Footrest Height Pivot Slide Tube Height Adjustment FigureInstalling 3-INCH Extension Figure Installing Elevating Legrests FigureProcedure Raising/Lowering Elevating LegrestsAdjusting Calfpads INSTALLING/ADJUSTING Adjustable Angle FLIP-UP FootplatesInstalling Adjustable Angle Flip-up Footplates Figure Adjustable Angle Flip-up Footplate Depth Adjustment FigureOptional Footrest Accessories Replacing Sector Block FigureFLIP-UP Footplates Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Adjusting the T Arms RemovingHeight Figure Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Arms Procedure Replacing the Locking Lever T Arms FigureTop Middle Bottom Side Arm Guard Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Adjustment ReplacementAngled Portion Cantilever Arm Locking Mechanism Actuator Apply LoctiteInstalling Fabric Clothing Guards Figure Adjusting Conventional Arm HeightInstalling Rigid Side Guards Figure Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure Procedure Back Installing Adjustable Back Upholstery FigureC K Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Adjusting the Back Height Adjustable Height Backs FigureRecliner Back Upholstery Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Changing the Back Angle Repositioning the Back Changing Seat DepthBack Plate Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure A T SeatCHANGING/REPOSITIONING Seat Rails Figure Replacing Seat Upholstery FigureProcedure Seat Repositioning the Crossbraces FigureChanging Seat Width Standard Folding Frames FigureFor installation of new Pivot LinkCrossbraces Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure REPLACING/REPAIRING Front Caster TIRE/TUBE CastersInline Caster Headtubes Figure Offset Caster Headtubes FigureCaster Headtube Mounting Adjustments Figure Height AdjustmentRepositioning the Caster Headtubes Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw REMOVING/INSTALLING Rear Wheels Figure Adjusting the QUICK-RELEASE Axle FigureA R Rear WheelsInstalling the QUAD-RELEASE Axle Figure Adjusting the QUAD-RELEASE Handle FigureJusting the QUAD-RELEASE Handle And/or OutHandrim Replacement Figure Removing the Play From the Rear WheelsSpoke Rear Wheels Phillips Bolt HandrimInstalling Projection Handrims Composite Rear Wheels FigureComposite Rim Locknut Spoke Rear Wheels FigureREPAIRING/REPLACING Rear Wheel TIRE/ Tube Adjusting the Wheelbase Length FigureJam Nuts Shortening ForwardAdjusting the Wheelbase Width Figure Adjusting Rear Wheel Height FigureAxle Mounting PlateAdjusting the Wheel Locks Figure Wheel Lock Extension Handle Installation FigureE E L K S E R S Wheel LOCKS/ANTI-TIPPERSProcedure Wheel LOCKS/ANTI-TIPPERS INSTALLING/ADJUSTING the ANTI-TIPPERSAdjusting the Anti-Tippers Figure Installing the Anti-Tippers FigureREPLACEMENT/ADJUSTMENT ReclinerRecliner Operation Figures 1 Folding/Unfolding the WheelchairInstalling New Recliner Cables Actuator Housing Cable Locking NutRecliner Trigger Release LeverReplacing the GAS Cylinders Figure Must Look TOO LOWLike this Steps 1, 5Adjusting the GAS Cylinders Figure Trigger Release Lever Cable Locking Nut AdjustingSqueeze the handles to extend the new gas cylinders Detail B Must Look TOO LOWSEAT-TO-FLOOR SEAT-TO-FLOOR Height DeterminationMinus EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights A T P T H Seat Depth Determination FigureChanging Seat Depth Seat DepthSeat Depth Checklist Seat DepthA T P T LeftRight Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents