Invacare 96-100 manual Installing Fabric Clothing Guards Figure, Adjusting Conventional Arm Height

Page 26

PROCEDURE 2

ARMS

A R M S

INSTALLING FABRIC CLOTHING GUARDS (FIGURE 14)

1.Remove the seat cushion, if necessary.

2.Secure the fastening straps of the fabric clothing pro- tectors to the seat upholstery.

3.Reinstall the seat cushion, if necessary.

4.Remove the two (2) phillips screws that secure the back upholstery to the back canes.

5.Position the D-rings on the mounting holes in the back canes.

6.Reinstall the two (2) phillips screws and securely tighten.

7.Run the nylon cord evenly through the two (2) D- rings.

5.Determine the necessary position for the rigid side guard.

6.Securely tighten the two (2) half clamps together with

the socket screw.

Socket Screw

Washer

Unthreaded Half Clamp

 

Rigid

Side

Guard

Threaded Half Clamp

Wheelchair Frame

FIGURE 15 - INSTALLING RIGID SIDE GUARDS

8.Run the nylon cord through the cord lock.

9.Push star wheel into cord lock to hold the nylon cord in place.

10.Tie a knot in the nylon cord and cut the excess, if desired.

Fabric Clothing

Guard

Fastening Strap

Seat Upholstery

Cord Lock

Phillips

 

Screw,

Phillips Screw,

D-ring

 

D-ring

Star

 

Wheel

Nylon Cord

FIGURE 14 - INSTALLING FABRIC CLOTHING

GUARDS

ADJUSTING CONVENTIONAL ARM HEIGHT, REMOVING OR REPLACING CONVENTIONAL ARMS (FIGURE 16)

WARNING

Make sure the armrest release levers are secured before using the wheelchair.

Adjusting Conventional Arm Height

1.Unlock the conventional arm by flipping the arm- rest release lever on the top front of the armrest to the UP (HORIZONTAL) position.

2.Adjust conventional arm to desired height.

NOTE: Height adjustment levers MUST be in the unlocked position when placing upper arm into the arm assembly.

3.Lock the conventional arm by pressing the release lever into the DOWN (VERTICAL) position when the desired armrest height is achieved.

Removing Conventional Arms

1.Unlock the conventional by turning the armrest release lever located on the side rail to the un- locked position.

INSTALLING RIGID SIDE GUARDS (FIGURE 15)

1.Position the unthreaded half clamp on the INSIDE of the wheelchair frame.

2.Position the threaded half clamp on the OUTSIDE of the wheelchair frame.

3.Install the washer and socket screw through the two

(2) half clamps and loosely tighten.

4.Slide the rigid side guard into the slot on the threaded half clamp.

2.Remove the conventional arm from the wheel- chair.

Replacing Conventional Arms

NOTE: Armrest release levers MUST be in the un- locked position when placing armrests into the arm sockets.

1.Position the conventional arm in the arm sockets and lock the conventional arm by turning the arm- rest release levers into the locked position.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsNON-RECLINERS Percentage of Weight DistributionUnoccupied Occupied ReclinersBending Forward SAFETY/HANDLING Functional Reach from a WheelchairFolding and Unfolding Wheelchair Sling Seat Model Wheelchairs Folding Recliners onlySling Seat Model Wheelchairs Unfolding Folding Solid Seat Model WheelchairsA T U R E S FeaturesFeatures Specifications SpecificationsC K a G I N G PackagingHandling N D L I N GSafety Inspection Checklist Safety Inspection Check ListI N T E N a N C E TroubleshootingMaintenance Adjusting Footrest Height Procedure Front RiggingsInstalling Footrests Figure Pivot Slide Tube Height Adjustment FigureProcedure Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure Raising/Lowering Elevating LegrestsInstalling Adjustable Angle Flip-up Footplates Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjustable Angle Flip-up Footplate Depth Adjustment FigureFLIP-UP Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure Aluminum or Composite Footplates FigureM S Procedure ArmsInstalling Height Figure Adjusting the T ArmsRemoving Width FigureArm Hex Screws Washers Reposition the arm tube on the T arm postArm Sockets Figure Top Middle Bottom Side Arm Guard Arms ProcedureReplacing the Locking Lever T Arms Figure Socket Screws Bottom ClampCorresponding Arm Adjustment to Back Angle Figures 10 Using FigureInstalling/Height Adjustment Figure Angled Portion Cantilever Arm AdjustmentReplacement Locking Mechanism Actuator Apply LoctiteInstalling Rigid Side Guards Figure Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Removing Conventional ArmsFront Arm Sockets Figure Replacing Armrest Pads FigureRear Arm Sockets Figure C K Procedure BackInstalling Adjustable Back Upholstery Figure Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsBack upholstery cover is designed for three 3 reasons WHY USE Adjustable Back Upholstery a Clinical DiscussionBack Upholstery Cover Recliner Back Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Headrest Upholstery FigureBack Cane Hex Bolt Washer Back Angle Plate Locknut Fixed Height Backs FigureSlowly remove the two 2 backs canes from the wheelchair Replacing the Locking Mechanism in the Back Cane Figure Back Plate Changing the Back AngleRepositioning the Back Changing Seat Depth Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureReplacing Folding Push Handle Recliners only Figure Installing and Removing a Seating SystemRecliner Brackets CHANGING/REPOSITIONING Seat Rails Figure A TSeat Replacing Seat Upholstery FigureChanging Seat Width Procedure SeatRepositioning the Crossbraces Figure Standard Folding Frames FigureCrossbraces For installation of newPivot Link Folding Frames Without Seat Rails FigureCrossmembers Wheelchair Frame Washer Hex Screws Hex Bolt Seat Width HolesRigid Frames Figure Replacing Front Fork Figure S T E R SCasters Inline Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Offset Caster Headtubes FigureRepositioning the Caster Headtubes Caster Headtube Mounting Adjustments FigureHeight Adjustment Inline Caster Headtube Hardware OffsetCover Headtube Locknut Cap Spacer Fork Stem Hex Screw Installing QUICK-RELEASE Casters FigureDust Release Detent Pin A R REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure Rear WheelsJusting the QUAD-RELEASE Handle Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure And/or OutSpoke Rear Wheels Handrim Replacement FigureRemoving the Play From the Rear Wheels Phillips Bolt HandrimComposite Rim Locknut Installing Projection HandrimsComposite Rear Wheels Figure Spoke Rear Wheels FigureJam Nuts REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Shortening ForwardAxle Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure Mounting PlateE E L K S E R S Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the Anti-Tippers FigureRecliner Operation Figures 1 REPLACEMENT/ADJUSTMENTRecliner Folding/Unfolding the WheelchairRecliner Installing New Recliner CablesActuator Housing Cable Locking Nut Trigger Release LeverLike this Replacing the GAS Cylinders FigureMust Look TOO LOW Steps 1, 5Squeeze the handles to extend the new gas cylinders Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Detail B Must Look TOO LOWMinus SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination EqualsStandard MULTI-POSITION Axle Plate Procedure SEAT-TO-FLOORChanging SEAT-TO-FLOOR Height A T Frame Inline Caster Headtube Front SEAT-TO-FLOOR HeightsLower Offset Caster Headtube Front SEAT-TO-FLOOR Heights Changing Seat Depth A T P T HSeat Depth Determination Figure Seat DepthSeat Depth Checklist Seat DepthRight A T P TLeft Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page R R a N T Y Limited WarrantyLimited Warranty One Invacare Way Technical Support
Top Page Image Contents