Invacare 96-100 Adjusting Calfpads, INSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates

Page 18

PROCEDURE 1

FRONT RIGGINGS

F

R O N T

R

I

G G I N G S

Adjusting Calfpads

1.To adjust the calfpad, turn pad towards the outside of the wheelchair.

2.Slide the calfpad up or down until the desired position is obtained.

3.To secure the calfpad, turn the calfpad towards the inside of the wheelchair.

INSTALLING/ADJUSTING ADJUSTABLE ANGLE FLIP-UP FOOTPLATES

WARNING

When determining the angle of the footplates, make sure the rear of the footplates do not interfere with the movement of the front casters.

Installing Adjustable Angle Flip-up Footplates (FIGURE 7)

1.Slide the half clamp over the footplate hinge.

2.Loosely tighten the two (2) flat bolts, washers and locknuts that secure the footplate to the half clamp.

3.If necessary, adjust the footplates to the necessary angle and depth for the user. Refer to the following sections of this procedure.

Adjustable Angle Flip-up Footplate Depth Adjustment (FIGURE 7)

2.Move the adjustable angle flip-up footplate to one

(1) of four (4) mounting positions.

3.Retighten the two (2) flat bolts, washers and lock- nuts.

NOTE: The settings for positioning the adjustable angle flip-up footplates on the half-clamps may vary for each footplate.

Adjustable Angle Flip-up Footplate Angle Adjustment (FIGURES 7 AND 8)

1.Loosen, but do not remove the two (2) flat bolts and locknuts that secure the adjustable angle flip-up footplate to the footplate hinge.

2.Position the adjustable angle flip-up footplate to the necessary angle to accommodate the user.

3.Retighten the two (2) flat bolts and locknuts.

Adjustable

Looking From

Angle Flip-up

Inside Towards

Footplate

the Outside of the

 

Wheelchair.

 

Footplate Hinge

FIGURE 8 - ADJUSTABLE ANGLE FLIP-UP

FOOTPLATE ANGLE ADJUSTMENT

1.Remove the two (2) flat bolts, washers and locknuts that secure the adjustable angle flip-up footplate to the footplate hinge.

NOTE: Observe the angle of the articulating footplate for reinstallation.

90o Footrest Support

Footplate Hinge

Flat Bolts

 

 

 

Adjustable

 

Nylon

Angle Flip-Up

 

Footplate

 

Adjustment

 

 

Screw

Half

 

 

Clamp

 

 

Washers

Half

 

Clamp

 

Locknuts

Footplate Hinge

 

FIGURE 7 - INSTALLING ADJUSTABLE ANGLE

FLIP-UP FOOTPLATES

Adjustable Angle Flip-up Footplate Perpendicular and/or Inversion/Eversion Adjustment (FIGURES 7 AND 9)

NOTE: It is not necessary to remove the footplate to perform this adjustment.

1.Insert a flathead screwdriver through the half clamp on the adjustable angle flip-up footplate.

2.Slowly turn the nylon adjustment screw in or out until the adjustable angle flip-up footplate is per- pendicular to the footrest assembly or the desired inversion/eversion is obtained.

Adjustable

Looking From the Front

Angle Flip-Up

Towards the Rear of

Footplate

the Wheelchair

Half Clamp

FIGURE 9 - ADJUSTABLE ANGLE FLIP-UP FOOTPLATE PERPENDICULAR AND/OR INVERSION/EVERSION ADJUSTMENT

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Allegro Special Notes Special NotesTable of Contents Safety Summary Safety SummarySafety Summary Recliner Option onlySAFETY/HANDLING of Wheelchairs Stairways Transferring to and from Other SeatsNON-RECLINERS Percentage of Weight DistributionUnoccupied Occupied ReclinersSAFETY/HANDLING Functional Reach from a Wheelchair Folding and Unfolding WheelchairBending Forward Sling Seat Model Wheelchairs Folding Recliners onlySling Seat Model Wheelchairs Unfolding Folding Solid Seat Model WheelchairsFeatures FeaturesA T U R E S Specifications SpecificationsC K a G I N G PackagingHandling N D L I N GSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceI N T E N a N C E Adjusting Footrest Height Procedure Front RiggingsInstalling Footrests Figure Pivot Slide Tube Height Adjustment FigureProcedure Installing 3-INCH Extension FigureInstalling Elevating Legrests Figure Raising/Lowering Elevating LegrestsInstalling Adjustable Angle Flip-up Footplates Figure Adjusting CalfpadsINSTALLING/ADJUSTING Adjustable Angle FLIP-UP Footplates Adjustable Angle Flip-up Footplate Depth Adjustment FigureFLIP-UP Footplates Figure Optional Footrest AccessoriesReplacing Sector Block Figure Aluminum or Composite Footplates FigureProcedure Arms InstallingM S Height Figure Adjusting the T ArmsRemoving Width FigureReposition the arm tube on the T arm post Arm Sockets FigureArm Hex Screws Washers Top Middle Bottom Side Arm Guard Arms ProcedureReplacing the Locking Lever T Arms Figure Socket Screws Bottom ClampUsing Figure Installing/Height Adjustment FigureCorresponding Arm Adjustment to Back Angle Figures 10 Angled Portion Cantilever Arm AdjustmentReplacement Locking Mechanism Actuator Apply LoctiteInstalling Rigid Side Guards Figure Installing Fabric Clothing Guards FigureAdjusting Conventional Arm Height Removing Conventional ArmsReplacing Armrest Pads Figure Rear Arm Sockets FigureFront Arm Sockets Figure C K Procedure BackInstalling Adjustable Back Upholstery Figure Replacing Back UpholsteryReplacing Adjustable Back Upholstery Figure Adjustable Tension StrapsWHY USE Adjustable Back Upholstery a Clinical Discussion Back Upholstery CoverBack upholstery cover is designed for three 3 reasons Recliner Back Upholstery Figure Adjusting the Back HeightAdjustable Height Backs Figure Recliner Headrest Upholstery FigureFixed Height Backs Figure Slowly remove the two 2 backs canes from the wheelchairBack Cane Hex Bolt Washer Back Angle Plate Locknut Replacing the Locking Mechanism in the Back Cane Figure Back Plate Changing the Back AngleRepositioning the Back Changing Seat Depth Non-Recliners FigureBack Angle Plate Hex Bolt Locknut Wheelchair Frame Washer Recliners FigureInstalling and Removing a Seating System Recliner BracketsReplacing Folding Push Handle Recliners only Figure CHANGING/REPOSITIONING Seat Rails Figure A TSeat Replacing Seat Upholstery FigureChanging Seat Width Procedure SeatRepositioning the Crossbraces Figure Standard Folding Frames FigureCrossbraces For installation of newPivot Link Folding Frames Without Seat Rails FigureHex Bolt Seat Width Holes Rigid Frames FigureCrossmembers Wheelchair Frame Washer Hex Screws S T E R S CastersReplacing Front Fork Figure Inline Caster Headtubes Figure REPLACING/REPAIRING Front Caster TIRE/TUBECasters Offset Caster Headtubes FigureRepositioning the Caster Headtubes Caster Headtube Mounting Adjustments FigureHeight Adjustment Inline Caster Headtube Hardware OffsetInstalling QUICK-RELEASE Casters Figure Dust Release Detent PinCover Headtube Locknut Cap Spacer Fork Stem Hex Screw A R REMOVING/INSTALLING Rear Wheels FigureAdjusting the QUICK-RELEASE Axle Figure Rear WheelsJusting the QUAD-RELEASE Handle Installing the QUAD-RELEASE Axle FigureAdjusting the QUAD-RELEASE Handle Figure And/or OutSpoke Rear Wheels Handrim Replacement FigureRemoving the Play From the Rear Wheels Phillips Bolt HandrimComposite Rim Locknut Installing Projection HandrimsComposite Rear Wheels Figure Spoke Rear Wheels FigureJam Nuts REPAIRING/REPLACING Rear Wheel TIRE/ TubeAdjusting the Wheelbase Length Figure Shortening ForwardAxle Adjusting the Wheelbase Width FigureAdjusting Rear Wheel Height Figure Mounting PlateE E L K S E R S Adjusting the Wheel Locks FigureWheel Lock Extension Handle Installation Figure Wheel LOCKS/ANTI-TIPPERSAdjusting the Anti-Tippers Figure Procedure Wheel LOCKS/ANTI-TIPPERSINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the Anti-Tippers FigureRecliner Operation Figures 1 REPLACEMENT/ADJUSTMENTRecliner Folding/Unfolding the WheelchairRecliner Installing New Recliner CablesActuator Housing Cable Locking Nut Trigger Release LeverLike this Replacing the GAS Cylinders FigureMust Look TOO LOW Steps 1, 5Squeeze the handles to extend the new gas cylinders Adjusting the GAS Cylinders FigureTrigger Release Lever Cable Locking Nut Adjusting Detail B Must Look TOO LOWMinus SEAT-TO-FLOORSEAT-TO-FLOOR Height Determination EqualsProcedure SEAT-TO-FLOOR Changing SEAT-TO-FLOOR HeightStandard MULTI-POSITION Axle Plate A T Inline Caster Headtube Front SEAT-TO-FLOOR Heights LowerFrame Offset Caster Headtube Front SEAT-TO-FLOOR Heights Changing Seat Depth A T P T HSeat Depth Determination Figure Seat DepthSeat Depth Checklist Seat DepthRight A T P TLeft Rear Mounting HoleApproximate 2-inch gap A T P T Inch Right A T P T H Page Limited Warranty Limited WarrantyR R a N T Y One Invacare Way Technical Support
Top Page Image Contents