Toshiba CTX manual Door Locks, Setting DND for Another Extension

Page 58

Advanced Operation

Door Lock(s)

Setting DND for Another Extension

To activate DND for another extension

Enter ￿￿￿￿￿ (hear Entry Tone) + the Primary extension of the remote extension + the pass code + ￿ (hear Success Tone). This sets DND as if activated by the Primary extension on the target telephone.

To deactivate DND for another extension

Enter ￿￿￿￿￿ (hear Entry Tone) + the Primary extension of the remote extension + the pass code + ￿ (hear Success Tone). This removes DND from the target telephone.

To change your DND Pass Code

Enter ￿￿￿￿ (hear Entry Tone) + ext. no. (hear Entry Tone) + old pass code + ￿￿ (hear Entry Tone) + new pass code + ￿￿(hear Success Tone).

If you activate DND while a call is ringing, the ringing stops. The LED continues to flash on your telephone and ring on other appearances.

Door Lock(s)

Your telephone may have 8QORFN￿'RRU button(s). Each 8QORFN￿'RRU￿button is programmed to unlock a specific door. Check with your CTX System Administrator to find out the locations of your system’s door phones and record them below.

Door Lock No.

Location

 

 

0

1

2

3

4

5

Door Lock No.

Location

 

 

6

7

8

9

10

To unlock a door

Press the specific 8QORFN￿'RRU button or ￿￿￿ + the Door Lock Number (see above table). The door unlocks for three~30 seconds (set in system programming). The Unlock Door LED is lit while the door is unlocked.

44

Strata CTX DKT/IPT Telephone 11/03

Image 58
Contents DKT/IPT Telephone User Guide Publication Information Toshiba America Information SYSTEMS, INC. Tais Toshiba America Information Systems, Inc Contents Advanced Operation Iii DKT3014 LCD Features Appendix a Centrex Application Appendix C IPT1020-SD Settings Introduction OrganizationHow to Use This Guide ConventionsRelated Documents/Media See FigureIntroduction Grand Tour DKT3000-series TelephonesGrand Tour Flexible Buttons Fixed ButtonsLiquid Crystal Display IPT1020-SD Telephones DKT2000-series TelephonesDKT2020-SD Telephone Line Buttons Important Read First BasicsWhat’s My Line? Which Outgoing/Incoming Call Features Do I Have? Spkr Button Making a CallHot Dialing HandsetSpeaker Switching Between Handset and SpeakerphoneAnswering a Call Handsfree AnswerbackMessage Waiting Responding to a Lit Msg LEDMicrophone Turning On/Off MW LED on Another ExtensionTo transfer a call directly to Voice Mail VM Call TransferTo perform Call Transfer Immediate To transfer conference control Conference CallsTo conference calls To hold a conference callConnecting Two Outside Lines Adding Voice Mail to a ConferenceConference Split/Join/Drop To Split from a conferenceTo Drop the Split party from a conference Automatic Hold HoldExclusive Hold Consultation HoldTo adjust the handset volume Volume ControlLCD Contrast Adjustments To adjust handset Beep ToneLCD Contrast Adjustments Using Your LCD Advanced OperationSoft Keys LineSoft Key Example To set an advisory message Advisory MessagesTo clear the registered message Verified/Non-Verified Account Codes To dial using Forced Account CodesAccount Code Calls Forced Account CodesTo enter an Account Code using access codes To dial using the Account Code buttonVoluntary Account Codes Verified/Non-Verified Automatic Busy Redial To cancel Automatic Busy RedialTo activate Automatic Busy Redial Automatic Callback To cancel ACBTo set Automatic Callback Background Music To enable background music on your telephone speakerTo cancel background music on your telephone speaker To change the BGM source 1~15 assigned to the BGM buttonSystem Call ForwardStation Call Forward Settings Station Call Forward CategoriesStation Call Forward Procedures To use the Call Forward button sequenceCall Forward Procedure Feature Button Sequence Call Forward ExamplesCall Forward Procedure Feature Button Sequence Advanced Operation An ext Call Park Orbits Call HistoryTo view Call History To park a call Call PickupGroup Pickup To retrieve a parked callRinging, Page or Held Call Pickup To perform Call PickupCall Waiting To answer a waiting call by placing the current call on holdDirect Station Selection Buttons Hotline Direct Inward System Access DisaTo connect directly to another station’s extension To set distinctive ringing CTX software R1.2 or lower Distinctive RingingTo set distinctive ringing CTX software R1.3 or higher To activate DND on a non-Primary extension Do Not DisturbTo activate DND on your Primary extension To deactivate DNDSetting DND for Another Extension Door LocksDoor Phones To answer a door phone callEmergency Monitoring Station Echo CancellationEmergency Call To call/monitor a door phoneMicrophone Cut-Off Emergency RingdownLanguage Codes To change the Language DisplayTo answer a Handset OCA call Off-hook Call AnnounceTo make an OCA call To answer a Speaker OCA callDo Not Disturb Override Override CallsBusy Override To use Busy OverrideTo perform Executive Override Executive OverrideDestination Restriction/Traveling Class Override To use Destination Restriction or Traveling Class OverridePaging Class of Service OverrideTo perform Class of Service Override Privacy OverrideEmergency Answering aAll Call To make an All CallRedial To set/cancel PrivacyPrivacy To use Privacy ReleaseMaking a Call Using Speed Dial Speed DialAccessing System SD and Personal SD Directories To access the SD directoriesAdvanced Speed Dial Operation DKT3014-SDL Name StorageTone/Pulse Dialing To change Tone DialingVoice Mail Direct Transfer Voice Mail Soft KeysAccept Soft Keys for CTX Digital Telephones Next Name Security Code Call Recording To record a callOther Voice Mail Features Pause/Resume RecordingDKT3014 LCD Features Directory and Speed Dial Listings Direct Station SelectionSystem Speed Dial and Personal Speed Dial Internal Directory and External DirectoryStoring Personal Speed Dial Names To assign Station Speed Dial namesPress 6SGLDO. The Speed Dial name is now programmed DKT3014 LCD Features Programming Feature Buttons User ProgrammingUser Programming Mode Flexible Button CodesSetting/Changing a Flexible Button’s Function Feature CodeOne Touch Buttons Changing a One Touch ButtonSetting/Changing a Personal Speed Dial Code To Use a One Touch ButtonFeature Codes Feature Access Codes Feature Access Code Sequences1 Messaging Advisory 6SGLDO4+QQQ LED Indicator Details LEDDADM/DSS Console Dadm Buttons and LEDsDSS Console DSS ButtonsTransferring to an Idle Station Calling a StationTo transfer a call to an idle station Speed Dial Call Transfer with Camp-onCall Answering Outside Line To transfer call to a busy stationNight Transfer Button PagingCall Forward Override DSS Override To override call forward with your DSS ConsoleFlexible Directory Numbering Centrex Feature ButtonsCentrex Application Ringing RepeatDelayed Ringing Button Labels DefinitionsLQH 3656 Button Labels IPT1020-SD Settings FB Buttons FB buttons for 10-button phonesFB buttons for 14-button phones Initializing the IPT1020-SD IPT-to-IP Network Connection InstructionsManual setting, then press +ROG. Press % IP Telephone Start Up Sequence Action LCD Indication RemarksIPT1020-SD Function Settings FB3Setting the IPT1020-SD Headset Transmit Volume Viewing IPT1020-SD Terminal InformationIndex 101102 103 104